GSi JK125P Скачать руководство пользователя страница 127

Страница: 127 / 186

GSI Group - Laser Division

JK300HP/JK300P/JK125P

Issue 2.0

Pre-installation and User Manual

Part No: 1EA300E01

Page

113 of 172

Refer to Figure 14 for item identification.

Step Action

WARNING
ELECTRIC SHOCK HAZARDS EXIST.
ELECTRIC SHOCK CAN CAUSE SERIOUS OR FATAL INJURY.

Carry out Power OFF Sequence.
Wait for 2 minutes. This ensures that the capacitors have discharged to a safe level.

ISOLATE AND LOCK OUT THE MAINS SUPPLY TO THE LASER.

Unlock and open the Laser Head lid.

Make sure that the hose is connected to the Beam Dump housing.

Unlock and open the front door.

Using the handle located on the Cooler assembly Tray, pull the tray out half way.

Remove the yellow cap from the top of the Reservoir Tank.

CAUTION

Always use new Coolant. Do not fill Laser with used Coolant as it could be
contaminated.

Fill the Reservoir Tank with Analar Grade 3 water until level reaches max line on
reservoir. Refer to the water specification in Section 3.3.2.2

Replace the yellow cap to the top of the reservoir tank.

If necessary, connect Cooler Node cable assembly.

Carry out the Power ON Sequence.

Allow the cooling system to run for 1 minute.

Carry out the Power OFF Sequence.

Inspect the pipework and fittings for any signs of leaks.

Rectify the cause of any leaks.

Check the Coolant level. Add more Coolant if necessary.

Using the handle located on the Cooler Assembly tray, carefully lift and install the
Cooler Assembly on the rail and slide it back into position.

Note

Check to make sure that no hose lines are twisted or pinched.

Close and lock the front door.

Carry out the Power ON Sequence.

Reset the water run-time hours to zero.

For reservoir operation, refer to the LaserView

software help file.

For touch screen operation, refer to Section 6.

Petitioners Canadian Solar Inc. and Canadian Solar (USA) Inc.

Ex. 1025, p. 113

Содержание JK125P



























































































































































































Результаты поиска

Содержание JK125P

Отзывы:

Бренды по названию

Популярные бренды

GSi JK125P, Руководство пользователя

Результаты поиска

Содержание JK125P

Отзывы:

Бренды по названию

Популярные бренды