GSi JK125P Скачать руководство пользователя страница 112 | Manualshive

Страница: 112 / 186

GSi JK125P Скачать руководство пользователя страница 112

GSI Group - Laser Division
JK300HP/JK300P/JK125P
Pre-installation and User Manual

Issue 2.0

Page 98 of 172

Part No: 1EA300E01

7.12.2 Warning 4n02 : Dumping Current

Meaning:

The Power Supply is dumping current following a shutdown.

Reset when current level falls below the threshold.

7.12.3 Warning 4n03 : Dump Resistors Cooling

Meaning:

The Power Supply has been restarted and stopped multiple times, building up heat in the
dump resistors, which requires dissipating before allowing a further restart.

Reset when accumulated cooling time has elapsed.

7.13 Shutter Warnings (Zone 5)

7.13.1 Warning 5n01 : Fibre Temperature

Meaning:

The fibre temperature switch has overheated.

Requires laser (alarm) reset to clear.

7.13.2 Warning 5n02 : Shutter Temperature

Meaning:

The shutter housing temperature switch has overheated.

Requires laser (alarm) reset to clear.

7.13.3 Warning 5n03 : FCMS

Meaning:

The fibre continuity circuit has broken.

Requires laser (alarm) reset to clear.

7.13.4 Warning 5n04 : External Work Chamber Doors

Meaning:

The work chamber doors failed to close simultaneously.

Requires laser (alarm) reset to clear.

7.13.5 Warning 5n05 : Close

Meaning:

The shutter failed to close within specified time.

Requires laser (alarm) reset to clear.

7.13.6 Warning 5n06 : Open

Meaning:

The shutter failed to open within the specified time.

Requires laser (alarm) reset to clear.

Petitioners Canadian Solar Inc. and Canadian Solar (USA) Inc.

Ex. 1025, p. 98

«
...
110
111
112
113
114
...
»

Содержание JK125P



























































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды