manualshive.com logo in svg

GSi JK125P, Руководство пользователя

Поделиться
Скачать
GSi JK125P Скачать руководство пользователя страница 101

 

GSI Group - Laser Division 

JK300HP/JK300P/JK125P 

Issue 2.0 

Pre-installation and User Manual 

Part No: 1EA300E01 

Page 

87 of 172 

7.5.6  Alarm 3n06: Cooler Module Relay Overload Fault 

Meaning: 

Circuit breaker supplying the pump has tripped. 

Possible causes: 

1. Faulty 

pump. 

2. Pump 

overheated. 

3. Loose 

connection. 

4. 

Faulty pump connections. 

7.5.7  Alarm 3n07: Low temperature fault 

Meaning: 

The coolant temperature has fallen below a configurable threshold. 

Possible causes:  

1. 

Incorrect cooler valve setting. 

2. 

Cooler valve stuck in the open position. 

3. 

Configurable threshold set too high. 

4. Loose 

connections. 

5. 

Faulty temperature sensor 

6. 

Faulty Cooler Module. 

7.5.8  Alarm 3n08: High temperature fault 

Meaning: 

The coolant temperature has raised above a configurable threshold. 

Possible causes:  

1. 

Incorrect cooler valve setting. 

2. 

Cooler valve stuck in the closed position. 

3. 

Factory supply cooling water turned off. 

4. 

Insufficient flow from factory cooling water supply. 

5. 

Configurable threshold set too low. 

6. Loose 

connections. 

7. 

Faulty temperature sensor. 

8. 

Faulty Cooler Module. 

7.5.9  Alarm 3n09: Very High temperature fault 

Meaning: 

The coolant temperature has raised above a fixed software temperature threshold. 

Possible causes:  

1. 

Configurable high temperature alarm level set too high. 

2. 

Incorrect cooler valve setting. 

3. 

Cooler valve stuck in the closed position. 

4. 

Factory supply cooling water turned off. 

5. 

Insufficient flow from factory cooling water supply. 

Petitioners Canadian Solar Inc. and Canadian Solar (USA) Inc. 

Ex. 1025, p. 87

Содержание JK125P



























































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды