manualshive.com logo in svg

GSi JK125P, Руководство пользователя

Поделиться
Скачать
GSi JK125P Скачать руководство пользователя страница 51

 

GSI Group - Laser Division 

JK300HP/JK300P/JK125P 

Issue 2.0 

Pre-installation and User Manual 

Part No: 1EA300E01 

Page 

37 of 172 

2.7.6 Workstation Interlock 

Where safety interlock switches are operated frequently, a RIC is not suitable.  In these 
circumstances, workstation interlocks are used. 

If the terminals of the workstation interlock are open-circuit (not electrically joined) then the 
Laser Shutter closes, preventing the Laser beam from emitting from the Laser. 

To enable Laser output, the terminals of the workstation interlock must be electrically joined, 
either by fitting a short-circuit link within the Shutter interlock plug or by connecting a safety 
interlock switch to the Shutter interlock plug. 

WARNINGS 
NO-ONE MUST ENTER AN AREA WHERE EXPOSURE TO HARMFUL 
LEVELS OF RADIATION IS POSSIBLE. 

DO NOT CLOSE THE SHUTTER BY MEANS OF THE SHUTTER CLOSE 
COMMAND OR FROM A REMOTE CONTROLLER AS A MEANS OF 
PREVENTING EXPOSURE TO LASER RADIATION. 

IF A SHUTTER INTERLOCK PLUG IS FITTED WITH A SHORT-
CIRCUITING LINK, THE PLUG MUST BE WITHDRAWN FROM THE 
SOCKET BEFORE ENTERING AN AREA WHERE LASER RADIATION 
IS LIKELY TO EXCEED THE CLASS 1 (I) LIMIT. 

 

IF THE LASER BEAM TERMINATES IN A CLASS 1 (I) WORK 
ENCLOSURE, THE ACCESS DOORS MUST BE PROTECTED BY 
SAFETY INTERLOCK SHUTTER SWITCHES CONNECTED TO THE 
SHUTTER INTERLOCK SOCKET. 

Petitioners Canadian Solar Inc. and Canadian Solar (USA) Inc. 

Ex. 1025, p. 37

Содержание JK125P



























































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды