GILES GEF-400 Скачать руководство пользователя страница 85

Страница: 85 / 115

GEF-VH Series Fryers Only

Ventless Hood

Take care not to bend the collection fins or break the ionizer wires when handling and

cleaning the Cell. Bent fins and broken wires can prevent the EAC from working properly,

and potentially void the factory warranty.

7.1.8

EAC Filter Cell Cleaning

The EAC Filter Cell must be cleaned

DAILY

to maintain peak hood performance.

• The EAC Filter Cell is NOT dishwasher safe ... DO NOT wash in the dishwasher!

•

DO NOT dry the Cell by running the Hood fan to air dry it. This could potentially damage

the EAC system causing improper operation and void the warranty.

•

DO NOT attempt to clean the Cell with cleaners which might be corrosive to aluminum.

1. Add

64 ozs.

of a mild degreaser concentrate, such as

Simple Green

Clear

Magic

, to the provided Soaking Tank

①

... add clean water to the fill line

marked on the inside of the Tank back and mix thoroughly.

2. Hold the EAC Cell by the Contact Plate

②

and carefully lower it into the

degreasing solution.

3. Allow the Cell to soak for about

30 minutes

. After that time, lift it by the

Contact Plate and jog up and down in the solution several times to help

dislodge grease residue.

4. Carefully remove Cell from the Soaking Tank and rinse thoroughly in sink,

using hot water spray.

DO NOT scrub with brush

5. Stand Cell on end, in a dish drainer, with Contact Plate up and allow it to air

dry overnight.

It is IMPORTANT that the Cell be completely dry before re-

installing in Hood for use.

6 Inspect for broken wires or bent fins. Broken wires should be promptly

replaced. Bent fins may be gently straightened by hand, if needed.

NOTE: The degreasing solution can be used for up to 30 days, or until a greasy

film remains visible on top of the liquid. Always be sure that solution

completely covers the Cell when soaking ... add water if needed..

Fins

Ionizer Wire

(9) required

Содержание GEF-400




















































































































Результаты поиска

Содержание GEF-400

Отзывы:

Похожие инструкции для GEF-400

Бренды по названию

Популярные бренды

GILES GEF-400, Руководство по эксплуатации и обслуживанию

Результаты поиска

Содержание GEF-400

Отзывы:

Похожие инструкции для GEF-400

Бренды по названию

Популярные бренды