GILES GEF-400 Скачать руководство пользователя страница 16

Страница: 16 / 115

Installation

Keep the appliance and surrounding area free and clear of combustible materials. GEF model = 3” [7.6 cm] ...

GEF-VH model = 18” [46 cm].

Allow for adequate space to allow easy access for future servicing and proper operation. Provide adequate

ventilation in the operating area, as required.

Be sure that electrical service available in the intended location is of a voltage and amp rating adequate to

power the appliance.

Be sure unit is to be installed in a stable position and will not unintentionally move. Unit has locking brakes

on front casters ... be sure they are locked. Some jurisdictions may require special anchoring of the

appliance; check local codes.

VH Model Only:

Depending on local code, room size, and other appliances operating in the space, exhaust

ventilation may be required to provide adequate air exchange. Often this can be accomplished by the

installation of an exhaust fan in the area where the appliance is installed. To determine requirements for

specific installation, supply the HVAC contractor the following information:

a. Hood exhausts between 510 to 680 CFM.
b. The average temperature of the exhausted air from the Hood, after four (4) hours of continuous frying, is

approximately 90°F (32°C).

This appliance is to be installed, used and maintained in accordance with the

Standard for Ventilation

Control, and Fire Protection of Commercial Cooking Operations, NFPA 96

These steps will help to ensure proper installation. If there are questions concerning these procedures, contact

Giles

Technical Support

800.554.4537

or email

[email protected]

This section provides a summary of procedures necessary for proper installation of the Giles Model GEF or GEF-VH

Series Fryer. To avoid potential for personal injury and/or equipment damage, please be sure the steps and procedures

are followed.

2.1

Appliance Location

NOTE (GEF-VH Models):

The sound level of the Hood when operating is approximately 65 dB.

GEF & GEF-VH Series Fryers

DO NOT MODIFY, ADD ATTACHMENTS OR OTHERWISE ALTER THIS EQUIPMENT

Содержание GEF-400




















































































































Результаты поиска

Содержание GEF-400

Отзывы:

Похожие инструкции для GEF-400

Бренды по названию

Популярные бренды

GILES GEF-400, Руководство по эксплуатации и обслуживанию

Результаты поиска

Содержание GEF-400

Отзывы:

Похожие инструкции для GEF-400

Бренды по названию

Популярные бренды