GILES GEF-400 Скачать руководство пользователя страница 44

Страница: 44 / 115

GEF & GEF-VH Series Fryers

Pre-Operation Checkout

4.4

Filter Pump Test

1. Follow steps in

Section 4-1

2. Place the Power Switch

①

in the

[ON]

position. Wait until Controller powers-up,

then press

[ALARM]

key to silence alarm.

3. Open Cabinet Door.

Disconnect and

remove Filter Pan if not done previously

4. Firmly press the palm of the hand over the

Filter Pan Quick Disconnect

②

fitting.

5. While covering the opening with the hand, set

the Pump Switch

③

to the

[FILTER PUMP]

position. The pump will start ... if suction is

felt, it is operating correctly. Return switch to

[OFF].

Allow pump to run

ONLY

long enough to

check for suction.

If no suction is felt, or if air seems to be

blowing out of the fitting, refer to the

troubleshooting procedures in

Section 8.2

otherwise see

Section 4.5

4.5

Perform Boil-Out Procedure

The following test confirms that the Filter Pump is operating properly.

Perform a Boil-Out Procedure to remove any dirt/debris that may have accumulated during shipment, or residue

remaining from manufacturing processes. See

Section 6.1, Boil-Out Procedure

. After the Boil Out procedure see

Section 4.6

[ALARM]

Содержание GEF-400




















































































































Результаты поиска

Содержание GEF-400

Отзывы:

Похожие инструкции для GEF-400

Бренды по названию

Популярные бренды

GILES GEF-400, Руководство по эксплуатации и обслуживанию

Результаты поиска

Содержание GEF-400

Отзывы:

Похожие инструкции для GEF-400

Бренды по названию

Популярные бренды