GILES GEF-400 Скачать руководство пользователя страница 61

Страница: 61 / 115

GEF & GEF-VH Series Fryers

Fryer Operation

5.1.10

Controller Errors & Alarms

ERROR CODE DESCRIPTION (OLED Display)

PROBLEM

OPEN

DRAIN IS OPEN

Drain valve is open, or not completely closed. Basket will be

raised if it is down. Close drain to clear error.

----

CHECK OIL LEVEL, ENSURE VAT IS

FULL, IF FULL THEN PRESS

[START]

This is a secondary error displayed after closing drain clears the

OPEN error; allows confirmation of oil level.

ER03

LOW OIL LEVEL – ENSURE VAT IS

FULL (Element/Add Level

Differential Warning)

The oil level is below the ADD line in the vat. Add oil to the FULL

level mark & stir. Error will remain in effect until temp

differential is resolved.

ER06

LOW OIL LEVEL – ENSURE VAT IS

FULL – PRESS [START]

(Post ER03 Warning)

After an ER03 is cleared, this is displayed until user presses

[START] to confirm oil level.

ER07

MAX ELEMENT TEMP – PRESS

[START] (Post Warning)

Error is displayed after MAX element temperature (ER19) has

occurred and the element has cooled below MAX temperature, .

ER13

OIL PROBE Error

Problem with the Variable Oil Temp Probe.

Service technician

required.

ER15

ELEMENT PROBE Error

Problem with the Element Temp Probe, typically attached

directly to heating element.

Service technician required.

ER17

ADD LEVEL PROBE Error

Problem with the Add Level Probe at vat ADD line. Fryer

without this Probe should have ELMT-ADD DIFF ENABLE setting

OFF

in FACTORY SETTINGS. Probe cannot be bypassed.

Service

technician required.

ER19

MAX ELEMENT TEMP Error

The maximum heating element temperature has been exceeded.

This is a safety device;

NEVER bypass this Probe.

ER21

BAFFLE FILTER MISSING

Ventless Fryers (VH) Only ...

Baffle Filter is missing, or

improperly installed.

ER22

CHARCOAL FILTER MISSING

Ventless Fryers (VH) Only ...

Charcoal Filter is missing, or

improperly installed.

ER23

FILTER CLOGGED

Ventless Fryers (VH) Only ...

pressure switch is not engaging.

Indicates airflow restriction; Charcoal Filter is clogged, or other

obstructions. Replace Filter, remove obstruction.

ER24

EAC CELL DIRTY

Ventless Fryers (VH) Only ...

EAC Filter Cell is dirty and needs to

be cleaned. This error can have also have other causes.

Continued on Next Page

Certain conditions, which can cause unsafe operation or damage to the unit, such as

open valves, low oil level, high temp, etc. will activate error

codes and sound an alarm tone. Error Codes will display on

the

Lower 7-Segment Display

; error information is shown on

the

Upper OLED Display

. Typically, the heating elements are

disabled until an error condition is corrected. Pressing the

[ALARM]

key silences the alarm tone, but does not clear the

error. Error Codes are shown on the following Table; details are presented in the

following section.

OLED

7-Segment

Содержание GEF-400




















































































































Результаты поиска

Содержание GEF-400

Отзывы:

Похожие инструкции для GEF-400

Бренды по названию

Популярные бренды

GILES GEF-400, Руководство по эксплуатации и обслуживанию

Результаты поиска

Содержание GEF-400

Отзывы:

Похожие инструкции для GEF-400

Бренды по названию

Популярные бренды