GILES GEF-400 Скачать руководство пользователя страница 63

Страница: 63 / 115

GEF & GEF-VH Series Fryers

Fryer Operation

5.1.10.1 Resolving Controller Errors & Alarms - continued

●

MAX ELEMENT TEMP Post-error Warning (Error Code 07)

- After

Error 19

is cleared, a warning alarm occurs.

The

Lower Display

shows

“Er07”

and the

Upper Display

reads

“MAX ELEMENT TEMP - PRESS [START]”

This

alarm alerts user that a maximum element temperature error occurred and is now cleared. Press

[START]

key

to enter

PREHEAT

mode. Heating Element will not turn

until

[START]

is pressed.

●

BAFFLE FILTER MISSING (Error Code 21 - ONLY Applies to VH Model, Ventless Fryers) -

Alarm tone sounds,

Lower Display

shows

“Er21”

and the

Upper Display

reads

“ERROR ALARM - BAFFLE FILTER MISSING”

Indicates that the Baffle Filter is missing or improperly installed. Heating Elements are disabled until the

condition is corrected. Install the Baffle Filter, or adjust its position; error will clear when Filter is properly

installed. See

Section 7.1.2. & 7.1.3, Baffle Filter Removal & Installation

●

CHARCOAL FILTER MISSING (Error Code 22 - ONLY Applies to VH Model, Ventless Fryers) -

Alarm tone sounds,

Lower Display

shows

“Er22”

and the

Upper Display

reads

“ERROR ALARM - CHARCOAL FILTER MISSING”

Indicates that the Charcoal Filter is missing or improperly installed. Heating Elements are disabled until the

condition is corrected. Install the Charcoal Filter, or adjust its position; error will clear when Filter is properly

installed. See

Section 7.1.10, Charcoal Filter Installation

●

CLOGGED FILTER (Error Code 23 - ONLY Applies to VH Model, Ventless Fryers) -

Alarm tone sounds,

Lower

Display

shows

“Er23”

and the

Upper Display

reads

“ERROR ALARM - CLOGGED FILTER”

. Indicates that the

internal pressure switch is not engaged, due to decreased airflow through the Hood. Generally means that the

Charcoal Filter is clogged, however other airflow restricting conditions will also cause the alarm. Heating

Elements are disabled until the condition is corrected. Replace the Charcoal Filter and/or check for any other

airflow restrictions; the error will clear when proper airflow is restored. See

Section 7.1.10 & 7.1.12, Charcoal

Filter Installation & Replacement

●

E.A.C. DIRTY (Error Code 24 - ONLY Applies to VH Model, Ventless Fryers) -

Alarm tone sounds,

Lower Display

shows

“Er24”

and the

Upper Display

reads

“ERROR ALARM - CLEAN THE EAC”

. Indicates that the Electronic Air

Cleaner (EAC) Cell is excessively dirty, missing, improperly installed, damaged, or has stopped functioning.

Heating Elements are disabled until the condition is corrected. Clean/check the EAC Cell; the error will clear

when the condition is resolved. See

Section 7.1.6 through 7.1.9, EAC Filter Operation & Cleaning

NOTE: If an error condition cannot be resolved, please contact a factory-authorized service agent, or call

800.554.4537 for Giles Technical Support.

Содержание GEF-400




















































































































Результаты поиска

Содержание GEF-400

Отзывы:

Похожие инструкции для GEF-400

Бренды по названию

Популярные бренды

GILES GEF-400, Руководство по эксплуатации и обслуживанию

Результаты поиска

Содержание GEF-400

Отзывы:

Похожие инструкции для GEF-400

Бренды по названию

Популярные бренды