GILES GEF-400 Скачать руководство пользователя страница 59

Страница: 59 / 115

GEF & GEF-VH Series Fryers

Fryer Operation

5.1.9

Start-up Procedure

5.1.9.1 Start-up Non-Ventless, GEF

1. Initially, be sure that the Selector Switch

①

is in the center

[OFF]

position.

2. Place the Power Switch

②

in the

[ON]

position.

The green Power Light

③

will illuminate.

The Computer Cooking Controller will power-
up, perform a memory check and then sound
an alarm tone. The message

“POWER

FAILURE [PRESS START TO PREHEAT]”

shown on the

Upper OLED Display

④

This

is normal

, intended to prevent the Fryer

from beginning to heat after a power interruption until attended by the operator. Pressing the

[START]

key silences the alarm and allows the Fryer to enter

PREHEAT

mode. The settings shown on the

Upper

Display

are the last used. The Controller will indicate that Fryer is heating, but until the Selector Switch

is placed in the

[COOK]

position, the heating elements will not turn

DO NOT

place

Selector Switch

[COOK]

position unless pot is filled with cooking oil, see

Section 5.2,

Cooking Procedures

5.1.8

PASSWORD Protection

It is possible to enable

PASSWORD

protection for certain Controller functions and settings. This feature is typically

factory-set as

DISABLED

. When the

PASSCODE ENABLE

= [

ON]

(enabled) in

FACTORY SETTINGS

, the Controller

prompts the User for a password before they can add or edit Menu Item Presets, enter a manual temperature

setpoint, enter or change a manual cook time setting, or access the User Settings Menu.

If you desire to have Password protection enabled, or have questions concerning this feature, call

Giles Technical

Services at 800.554.4537

to request the passcode and instructions as to how to enable this feature.

NOTE:

Pressing the

[ALARM]

key

⑤

will

silence alarm tones. Alarm also

silences automatically after a preset

time expires. See

USER SETTINGS

Содержание GEF-400




















































































































Результаты поиска

Содержание GEF-400

Отзывы:

Похожие инструкции для GEF-400

Бренды по названию

Популярные бренды

GILES GEF-400, Руководство по эксплуатации и обслуживанию

Результаты поиска

Содержание GEF-400

Отзывы:

Похожие инструкции для GEF-400

Бренды по названию

Популярные бренды