GILES GEF-400 Скачать руководство пользователя страница 60

Страница: 60 / 115

GEF & GEF-VH Series Fryers

Fryer Operation

5.1.9.2 Start-up Ventless, GEF-VH

Be certain that all Hood Filters are properly installed, and that the Filter Access Cover is in

place and securely latched before attempting to operate the appliance.

1. Initially, ensure that the Selector Switch

①

is in the center

[OFF]

position.

2. Place the Power Switch

②

in the

[ON]

position. The green Power Light

③

will illuminate. The Computer

Cooking Controller will power-up, perform a memory check and then sound an audible alarm tone. The
message

“POWER FAILURE [PRESS START TO PREHEAT]”

is shown on the

Upper OLED Display

④

This is

normal

, intended to prevent the Fryer from beginning to heat after a power interruption until attended by the

user. Pressing the

[START]

key silences the alarm and allows the Fryer to enter the

PREHEAT

mode. The

settings shown on the

Upper Display

are the last used. The Controller will indicate that the Fryer is heating, but

until the Selector Switch is placed in the

[COOK]

position, the heating elements will not turn

[ON]

5. The Fryer Hood fan will start-up and the E.A.C. status

light

⑤

will illuminate.

DO NOT

place

Selector Switch

[COOK]

position unless pot is filled with cooking oil, see

Section 5.2, Cooking

Procedures

NOTE:

The appliance will NOT power-up if the Filter Access Cover is missing or ajar. The sides of

the Cover must seat flush against the Hood front and the pin on the right-hand edge must

engage the interlock switch inside the Hood wall.

NOTE:

Pressing the

[ALARM]

key

⑥

will

silence alarm tones. Alarm also

silences automatically after a preset

time expires. See

USER SETTINGS

Содержание GEF-400




















































































































Результаты поиска

Содержание GEF-400

Отзывы:

Похожие инструкции для GEF-400

Бренды по названию

Популярные бренды

GILES GEF-400, Руководство по эксплуатации и обслуживанию

Результаты поиска

Содержание GEF-400

Отзывы:

Похожие инструкции для GEF-400

Бренды по названию

Популярные бренды