GILES GEF-400 Скачать руководство пользователя страница 8

Страница: 8 / 115

vii

Safety

GEF Series

GEF-VH Series

Safety Overview:

The instructions contained in this manual have been prepared to aid in learning the proper procedures for installing,

operating and servicing the

Giles Model GEF or GEF-VH Series Electric Fryer

Throughout the manual, safety precautions are identified by a hazard alert symbol and key words such as

DANGER,

WARNING

CAUTION

. Alert information precedes the tasks to which it applies. Suggested, recommended, or

other noteworthy information is identified as

NOTES

, or will be noted as

IMPORTANT!

. Additionally, certain words

are used to indicate a specific meaning, or to add emphasis as follows:

Shall:

understood to be mandatory.

Should:

understood to be advisory.

May:

understood to be permissive.

Will:

indicates a future event or condition to occur.

Hazard Alert Symbols

are used in conjunction with key words, such as

DANGER, WARNING

, or

CAUTION,

to alert Users to potential personal injury hazards and/or poor operating practices. These will

immediately precede precautionary measures pertaining to avoiding such hazards or practices. Adhere to all

information following these symbols to avoid possible injury, or even death. Failure to do so may also void the

factory warranty.

Indicates an imminently hazardous situation which, if not avoided, will result in serious personal injury, even

death.

Indicates a potentially hazardous situation which, if not avoided, could result in serious injury, even death.

Indicates a potentially hazardous situation which, if not avoided, may result in minor to moderate injury. This

notification is also used as an alert to unsafe practices.

If used without the safety alert symbol, indicates a potentially hazardous situation which, if not avoided, may

result in equipment and/or property damage, and may void the factory warranty.

NOTE or IMPORTANT!

Identifies suggested, recommended, or other important information.

Содержание GEF-400




















































































































Результаты поиска

Содержание GEF-400

Отзывы:

Похожие инструкции для GEF-400

Бренды по названию

Популярные бренды

GILES GEF-400, Руководство по эксплуатации и обслуживанию

Результаты поиска

Содержание GEF-400

Отзывы:

Похожие инструкции для GEF-400

Бренды по названию

Популярные бренды