GILES GEF-400 Скачать руководство пользователя страница 75

Страница: 75 / 115

GEF & GEF-VH Series Fryers

Cleaning

6.1

Boil-Out Procedure (Cleaning the Fry Pot)

. Remove cooking oil from the unit, see

Section 5.4, Removing Used

Waste Cooking Oil from Fryer

. Wipe out any heavy oil residue with

paper towels.

2. Ensure the Drain Valve

①

is in the

[CLOSE]

, vertical position and the

Power Switch

③

is in the

[OFF]

position.

3. Fill the Fry Pot with fresh clean water to the

FULL

level

②

Giles Boil-Out #72003

is the recommended cleaning product. Follow

the directions on the container, and add the prescribed amount of

Boil-Out powder to the water. Stir gently to mix.

If using a cleaner other than Giles Boil-Out closely follow the

manufacturer’s usage instructions. Many commercially available

cleaners contain caustic chemicals, which require special precautions.

If used improperly, these chemicals may damage the equipment

and/or cause personal injury to the user.

MAX

FULL

ADD

This section describes cleaning procedures for GEF & GEF-VH Series Fryers. Typically, general cleaning should be

performed daily.

This section explains how to clean the Fry Pot using the

Boil-Out Procedure

. A Boil-Out must be performed before

cooking on new equipment, and should be performed each time before fresh oil is added after used cooking oil is

removed from Fryer and discarded.

IMPORTANT! For proper cooking performance and Fryer operation, the Boil-

Out procedure should be performed at least every 10 to 14 days.

•

The Boil-Out process does not require a rolling boil, however, DO NOT leave the Fryer unattended during the

procedure. Fryer should be carefully monitored for accidental overflow, that may result in serious equipment

damage.

•

The boil-out solution and the Fryer will be HOT at end of the cycle ... always wear thermal protection when

draining and cleaning.

6. Cleaning

•

DO NOT wash down the unit interior or exterior with water from a spray hose or any pressure-type washer.

•

Failure to comply with DANGER notices will result in death or serious injury, equipment or property damage,

and void the warranty.

Continued on Next Page

Содержание GEF-400




















































































































Результаты поиска

Содержание GEF-400

Отзывы:

Похожие инструкции для GEF-400

Бренды по названию

Популярные бренды

GILES GEF-400, Руководство по эксплуатации и обслуживанию

Результаты поиска

Содержание GEF-400

Отзывы:

Похожие инструкции для GEF-400

Бренды по названию

Популярные бренды