GILES GEF-400 Скачать руководство пользователя страница 68

Страница: 68 / 115

GEF & GEF-VH Series Fryers

Fryer Operation

5.3

Filtering Cooking Oil

1. After cooking the preset number of loads

[FILTER COUNT]

, an alarm will sound.

2a. If

FORCE FILTER = OFF

, display

①

reads

“

ALARM - FILTER OIL”

, press

[ALARM]

key

②

to continue. To alert operator that oil needs

filtering, this alarm reminder will occur after each

subsequent load cooked until oil is filtered.

2b. If

FORCE FILTER = ON

, display

①

reads

“

ALARM - MUST FILTER OIL”

, press

[ALARM]

key

②

. The Fryer is

locked-out of further

operation

until a filtering cycle is performed.

3. Place the Selector Switch

③

[OFF]

position.

Power Switch must remain ON.

4. Open the Cabinet Door, disconnect the Filter Pan Quick-

Disconnect Hose

④

and remove the Filter Pan

⑤

from

the unit.

5. Remove Pan Cover

⑥

to confirm that the Filter Media is

installed correctly (1 sheet of Filter Paper).

6. Distribute approx. 5 oz. of Filter Powder

(1-pack, Giles

#72004)

over filter media surface. It is important that a

suitable filter aid be used for removal of soluble impurities
and reconditioning of the oil.

7. Replace Filter Pan Cover

⑥

and reposition the Filter Pan

under the unit. Reconnect the Filter Pan Quick Disconnect

Hose

④

DO NOT attempt to filter cold, congealed oil. The Filter Pump can clog and be damaged.

Oil must be a minimum of 200°F (93°C) before attempting to pump.

This section explains use of the built-in Oil Filtration System for filtering and reconditioning used cooking oil. The

system circulates oil through filter media in the Filter Pan and back to the Fry Pot. Routinely performing procedure

can increase useful life of cooking oil by as much as 50%.
The Controller’s

[FORCE FILTER]

feature, in conjunction with a

[FISH FILTER] Menu Item setting (see

Section 5.1.4.1,

Editing a Menu Item Preset

can force Users to filter Fryer oil according to a set routine. Controller can place the

Fryer into

FILTER MODE

after a certain number

(FILTER COUNT)

of cook cycles have been completed. When feature

is turned

[ON]

, the Fryer will be

locked-out to prevent further operation

, after count is exceeded, until a filtering

cycle is performed. When feature is turned

[OFF]

, Controller will

only prompt

User to filter oil, after count is

exceeded. The prompting continues after every subsequent load until filtering is performed.

See

Section 5.1.7, User Settings

for more detail.

Factory-default: FORCE FILTER = [ON] ... FILTER COUNT=4 ... FISH

FILTER=[OFF].

FORCE FILTER SNOOZE

setting can allow one (1) additional cook cycle after the filter count is exceeded.

Factory-

default = [OFF].

Setting may be changed in

USER SETTINGS

Always wear thermal protection, such as Gloves or Oven Mitts, while performing the

filtering process. Fryer parts inside the cabinet will be extremely HOT!

Continued on Next Page

Содержание GEF-400




















































































































Результаты поиска

Содержание GEF-400

Отзывы:

Похожие инструкции для GEF-400

Бренды по названию

Популярные бренды

GILES GEF-400, Руководство по эксплуатации и обслуживанию

Результаты поиска

Содержание GEF-400

Отзывы:

Похожие инструкции для GEF-400

Бренды по названию

Популярные бренды