GAS BreathSpec Скачать руководство пользователя страница 156 | Manualshive

Страница: 156 / 242

background image

BreathSpec®

– User Manual

156/242

9.12 Workflows: File Transfer Setup

9.12.1 Overview

Files can be transferred to and from the device by LAN connection and by USB
device connected to the USB port at the front of the housing.

INFORMATION!

A connected USB device is always preferred to a LAN connection
when exporting or importing files manually.

INFORMATION!

The USB device must be formatted to FAT32. Consult your system
administrator on formatting USB devices.

Generated measurement files and measurement result files are stored on the internal
storage volume of the device.

The following file types are generated from measurements:

File Type

Description

MEA Measurement Files

Contains the complete data of one single
measurement including the raw sampling data.

When a connection to a server is established and the export is activated these files
are copied to this server when created in the workflow. Measurement files once
copied to one of these locations are marked and will be overwritten in case the
internal storage is full.
By default, the

Service Message Block Protocol (SMB)

also known as Common

Internet File System (CIFS) is used. The

Secure File Transfer Protocol (SFTP)

or a

modified version of the

Trivial File Transfer Protocol (TFTP)

can also be used.

LAN file transfer settings can be modified in

System

›

Transfer

›

Connection

›

Edit

Server Details

.

Manual transfer of measurement files stored on the device can be done

System

›

Transfer

›

Mea Files

›

Copy to Remote

.

Manual transfer of measurement files stored on the device can be done

System

›

Transfer

›

Mea Files

›

Delete

.

«
...
154
155
156
157
158
...
»

Содержание BreathSpec



















































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для BreathSpec

Бренд: Accurate Logic Страницы: 50

Acuvim-L Series

Бренд: AccuEnergy Страницы: 188

Бренд: VAMP Страницы: 78

Бренд: Keeler Страницы: 68

Бренд: Velleman Страницы: 107

Бренд: Fluke Calibration Страницы: 13

Бренд: Alfa Laval Страницы: 18

Бренд: SANKO Страницы: 97

Бренд: Staco Energy Страницы: 2

Бренд: GAGEMAKER Страницы: 36

GRAND RHAPSODY PIANO

Бренд: Waves Страницы: 19

Бренд: RaySafe Страницы: 2

LaserRange-Master T4 Pro

Бренд: LaserLiner Страницы: 68

Бренд: Trotec Страницы: 3

Бренд: Cressi Страницы: 36

The Beast 30W Plus - head

Бренд: Laboga Страницы: 16

Бренд: LOVATO ELECTRIC Страницы: 9

Бренд: Hanna Instruments Страницы: 84

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды