GAS BreathSpec Скачать руководство пользователя страница 54

Страница: 54 / 242

BreathSpec®

– User Manual

54/242

Recording Check Box

The live monitoring of measurements can
be recorded manually. The available
storage capacity in minutes is displayed.

Drift Voltage Mode

Displays the current selected Drift
Voltage state (positive / negative).

Device Parameter

Displays the current temperature, flow
and pressure values.

6.2.2 Measurement modes

Two measurement modes are available:

•

Measurement with user defined programs

•

Manually operated measurement

6.2.2.1 Measurement with user defined programs

In this mode data acquisition with user-defined measurement programs can be started.

The executable measurement program can be created and selected in the Programs

Window. The name of the current selected program is displayed in the upper left of the

Spectra Window. The selected measurement program can be started by activating the

Program button in the upper left of the Spectra Window.

Figure 21: Start Program

Содержание BreathSpec



















































































































































































































































Результаты поиска

Содержание BreathSpec

Отзывы:

Похожие инструкции для BreathSpec

Бренды по названию

Популярные бренды

GAS BreathSpec, Руководство пользователя

Результаты поиска

Содержание BreathSpec

Отзывы:

Похожие инструкции для BreathSpec

Бренды по названию

Популярные бренды