GAS BreathSpec Скачать руководство пользователя страница 139

Страница: 139 / 242

BreathSpec®

– User Manual

139/242

9.3.4 Workflow: Execution of an ambient air measurement using the Handheld

The analysis of the ambient air may indicate volatile compounds that do not originate

from the subject/patients breath but are present in the air.

To analyze the ambient air follow the steps described in 9.3.2. A Reservoir tube and

Mouthpiece must not be installed.

9.4 Workflow: Breath Sampling via Disposable Breath Sampler

9.4.1 Start a breath measurement using disposable breath sampler

INFORMATION!

To sample via the Luer-Lock-Adapter the respective tube port has to be
installed

see chapter 7.5

DANGER

•

Biohazard: wear appropriate gloves at all handling steps

•

Take measures to prevent contamination from one subject/patient

to other

WARNING

•

Pinching possible

Press Start Button to
initialize

the

selected

program.

The

dialog

‘Start progam’

appears.

Содержание BreathSpec



















































































































































































































































Результаты поиска

Содержание BreathSpec

Отзывы:

Бренды по названию

Популярные бренды

GAS BreathSpec, Руководство пользователя

Результаты поиска

Содержание BreathSpec

Отзывы:

Бренды по названию

Популярные бренды