manualshive.com logo in svg

GAS BreathSpec, Руководство пользователя

Поделиться
Скачать
GAS BreathSpec Скачать руководство пользователя страница 224

BreathSpec® 

– User Manual 

 

224/242 
 

Action 

Repeat the procedure. Restart the system and repeat the 

procedure. Check write protection of the USB-Stick. Ensure 

that the USB-Stick is FAT32 formatted. Reformat the USB-

Stick. Replace the USB-Stick with a new one. Repeat the 

procedure.

 

If that still does not help contact the G.A.S. 

service hotline. 

Error message 

Do you really want to relabel loop volume? It will be 

stored in all following measurements. 

Description 

Sample loop setting is change manually. 

Action 

Confirm or abort the dialog. 

Error message 

Can't set static ip! 

Description 

Setup of the static IP-address failed. 

Action 

Check the network settings. Contact your adminstrator. 

Repeat the procedure.

 

If that still does not help contact the 

G.A.S. service hotline. 

Error message 

Can't request DHCP: 

Description 

Setup of the dynmaic IP-address failed.

 

Action 

Check the network settings. Check DHCP-server. Contact 

your adminstrator. Repeat the procedure.

 

If that still does not 

help contact the G.A.S. service hotline. 

Error message 

Valve set to Inject. Loop not filled 

Description 

Valve setting is set to position “Inject” and not to “Fill loop”. 

Sample loop could not be filled. 

Action 

Abort program and set valve to 

position „Fill loop“ manually. 

Error message 

Trigger recieved while running program. 

Description 

During the program run a new trigger signal will be received. 

The program run is aborted. 

Содержание BreathSpec



















































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды