GAS BreathSpec Скачать руководство пользователя страница 25 | Manualshive

Страница: 25 / 242

background image

BreathSpec®

– User Manual

25/242

2.4 Dangers

The device and its equipment is subject to an endangerment analysis. The
construction and execution of the device corresponds to the today's state-of-the-art.
The device is reliable in service when operated according to its intended use.

INFORMATION!

If the housing of the device is damaged, the device must not be used
anymore and must be returned to the G.A.S. by using the original
transportation case.

DANGER

The BreathSpec®

device contains a radioactive radiation Tritium

source  of  75  MBq  which  in  all  EURATOM  countries  is  below  the
exemption  limit.  Do  not  open  the  device!  Do  not  try  to  recover
malfunctions  of  the  device!  Malfunction  recovery,  repairs  and  any
maintenance work may only be performed by G.A.S. or by qualified
personnel authorized by G.A.S.

DANGER

The BreathSpec®

and its equipment is not certified for the

employment in areas with explosive gas air mixtures (Zone 0).

DANGER

Exercise great care in handling current-carrying parts like the power
supply cord. Do not get directly in touch with current-carrying parts.
Do not open the housing. Do not use damaged parts.

DANGER

All parts of the equipment that are in contact with human breath must
either be disposed of or sanitized to prevent biohazard

DANGER

When Nitrogen is used as drift gas and helium as carrier gas,
ignition of a helium plasma may occur due to the high voltage
present in conjunction with a radiation source. This can damage the
IMS.

«
...
23
24
25
26
27
...
»

Содержание BreathSpec



















































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для BreathSpec

Бренд: Landis+Gyr Страницы: 10

Бренд: Kane Страницы: 16

Бренд: Kane Страницы: 60

Бренд: Vaisala Страницы: 90

Бренд: Vaisala Страницы: 4

Бренд: Hama Страницы: 16

Бренд: Olimpus Страницы: 12

Бренд: Motortech Страницы: 142

Бренд: Cecomp Страницы: 4

Бренд: PITSID Страницы: 22

Бренд: Swan Analytical Instruments Страницы: 102

Microlog GX Series

Бренд: SKF Страницы: 342

Бренд: Maico Страницы: 2

Бренд: Bahco Страницы: 21

Бренд: Kübler Страницы: 72

Бренд: Hanna Instruments Страницы: 16

Бренд: SAND Страницы: 15

Бренд: SNV Engineering Страницы: 43

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды