GAS BreathSpec Скачать руководство пользователя страница 89

Страница: 89 / 242

BreathSpec®

– User Manual

89/242

6.7.4 System Transfer Window

Figure 54: Operating Interface - System Transfer Window

MEA Files:

The current number of internal stored
measurement files and the following
measurement file managing options are
displayed and available:

Copy to USB:

Copy all internal stored

measurements to a connected USB
device.

Copy to remote:

All internal stored

measurement files will be copied to the
connected shared folder.

Delete:

Deleting all internal stored

measurement files.

Export:

Activating the automatic storage to a
connected shared folder on a network as
storage location for measurements.

Connection:

With

Edit Server Details Button

the

Export settings (transfer protocol, IPv4-
adress, shared folder name) can be set.

Содержание BreathSpec



















































































































































































































































Результаты поиска

Содержание BreathSpec

Отзывы:

Похожие инструкции для BreathSpec

Бренды по названию

Популярные бренды

GAS BreathSpec, Руководство пользователя

Результаты поиска

Содержание BreathSpec

Отзывы:

Похожие инструкции для BreathSpec

Бренды по названию

Популярные бренды