Fuji Xerox DocuPrint C2120 Скачать руководство пользователя | Manualshive

Страница: 96 / 206

background image

96

5 Control Panel Menus

PDF

Specifies the settings for PDF.

PHD Unit Refresh

Cleans the surface of the drum cartridge.

Print Meter

Initializes the meter counts.

Initialize NVM

Initializes the settings stored in the NVM except for the network settings. The
NV memory is nonvolatile memory that retains the settings of the printer even
when its power is switched off. After executing this function and restarting the
printer, all the menu options are reset to their default values.

Note

• You cannot execute this menu during printing.
• You need to restart the printer to activate this setting. After making the

setting, switch the printer off and then on again.

Storage Disk

Use this menu to delete all of the data in the RAM disk.

Note

• [Storage Disk] appears only when the additional memory (optional) is

installed.

Item

Description

Quantity

Sets the print quantity.
• [1 Set (s)] to [999 Set (s)] (default: [1 Set (s)])

Note

• Depending on the protocol used for file transmission, the value specified on

the protocol may override the [Quantity] setting.

2 Sided Print

Sets whether to enable 2 sided printing.
• [1 Sided] (default)

Disables 2 sided printing.

• [Long Edge Flip]

Prints on both sides of a paper so that the long edges of the documents are
bound.

• [Short Edges Flip]

Prints on both sides of a paper so that the short edges of the documents are
bound.

Note

• [2 Sided Print] appears only when the optional Duplex Unit is installed.

Print Mode

Sets the print mode to one of the following:
• [Normal] (default)

Prints documents at standard speed with standard image quality.

• [High Quality]

Produces higher image quality than [Normal], but at a lower print speed.

• [High Speed]

Prints documents at a higher speed than [Normal].

Password

Before printing a password-protected PDF, set the password here. The file will
be printed only if its password matches the password you set here.
The password can be up to 32 alphanumeric characters.

Collated

Sets whether to collate multiple-set documents. (1, 2, 3..., 1, 2, 3...)
• [Off] (default)
• [On]

Item

Description

«
...
94
95
96
97
98
...
»

Содержание DocuPrint C2120















































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для DocuPrint C2120

Pixma G1000 series

Бренд: Canon Страницы: 2

Pixma G1000 series

Бренд: Canon Страницы: 80

IMAGERUNNER ADVANCE C5051

Бренд: Canon Страницы: 44

Бренд: Oki Страницы: 24

Бренд: VAF instruments Страницы: 24

Бренд: 3DP Страницы: 12

Бренд: Ier Страницы: 8

Бренд: IBM Страницы: 102

Бренд: Oki Страницы: 36

Бренд: Oki Страницы: 3

Бренд: MakerBot Страницы: 48

Бренд: Canon Страницы: 2

Бренд: Intamsys Страницы: 5

Бренд: Konica Minolta Страницы: 102

Digital Minilab Frontier LP5700R

Бренд: FujiFilm Страницы: 2

ZPS3611 - QUICK

Бренд: Zonet Страницы: 1

Бренд: Copystar Страницы: 4

Бренд: Canon Страницы: 37

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды