Fuji Xerox DocuPrint C2120 Скачать руководство пользователя | Manualshive

Страница: 119 / 206

background image

6.6 Error Messages (In Alphabetical Order)

119

Remove & Shake
X Crtrdg

XXX=Yellow, Magenta, Cyan, or

Black

This message is displayed when the color printed with the X toner cartridge becomes
pale. Remove the X toner cartridge, and lightly shake it 5 to 6 times to even the toner.
Then, set the X toner cartridge at its original position.

Important

• Do not remove the toner cartridge except when required.

When removing the toner cartridge, the toner may scatter.

Refer to

• "Replacing the Toner Cartridges" (P. 128)

Remove PHD Unit
Tapes Mismatch

Ribbons remain in the drum cartridge. Remove the yellow ribbons from the drum
cartridge.

Refer to

• "Replacing the Drum Cartridge" (P. 130)

Replace PHD Unit

It is time to replace the drum cartridge.
Replace the drum cartridge with a new one.

Refer to

• "Consumables" (P. 182)
• "Life of Consumables" (P. 183)
• "Replacing the Drum Cartridge" (P. 130)

Replace XXX
Crtrdg

XXX=Yellow, Magenta, Cyan, or

Black

The X toner cartridge has run out of toner.
Replace the displayed toner cartridge with a new one.

Refer to

• "Life of Consumables" (P. 183)
• "Replacing the Toner Cartridges" (P. 128)

13_Replace XXX
Crtrdg

Check Toner Cart
YYY

Check Toner Cart
Replacement Time

XXX=Yellow, Magenta, Cyan,

or Black

YYY=Fuser Unit, Drum Cartridge,

belt unit

This message is displayed when the following two conditions are met.
1. The black toner cartridge is empty or the waste toner fills up the drum cartridge.
2. The fuser unit, the belt unit, or the drum cartridge reaches its life.

Replace the XXX toner cartridge and the YYY unit.
If the belt unit is displayed for YYY, call our Customer Support Center or your dealer.

Refer to

• "Replacing the Toner Cartridges" (P. 128)
• "Replacing the Fuser Unit" (P. 134)
• "Replacing the Drum Cartridge" (P. 130)
• "Consumables" (P. 182)

Set Fuser
in Place

Then Reboot
Printer

The fuser unit is not installed correctly. Open the front cover and re-install the fuser
unit. After installing the unit, turn on the printer.

Refer to

• "Replacing the Fuser Unit" (P. 134)

XXX Crtrdg
Mismatch

XXX=Yellow, Magenta, Cyan, or

Black

X is not a toner cartridge suitable for the printer.
Correctly set a suitable toner cartridge in the printer.

Refer to

• "Consumables" (P. 182)
• "Replacing the Toner Cartridges" (P. 128)

Message

Condition/Reason/Action

«
...
117
118
119
120
121
...
»

Содержание DocuPrint C2120















































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для DocuPrint C2120

Бренд: LabelTac Страницы: 2

Бренд: WANHAO Страницы: 5

Бренд: Wang Страницы: 24

Бренд: Samsung Страницы: 549

imageRUNNER 5075

Бренд: Canon Страницы: 250

Бренд: Canon Страницы: 2

imageRUNNER C3480

Бренд: Canon Страницы: 92

Бренд: Oki Страницы: 328

Бренд: MEFA Страницы: 2

Бренд: Xerox Страницы: 200

WorkCentre Pro 90

Бренд: Xerox Страницы: 36

Бренд: Xiamen Hanin Electronic Technology Страницы: 62

Бренд: Labelmate Страницы: 61

Бренд: Tally Страницы: 266

Бренд: Shandong New Beiyang Information Technology Co. Страницы: 47

D-color MF 250 Plus

Бренд: Olivetti Страницы: 276

Бренд: Aficio Страницы: 92

Бренд: Sartorius Страницы: 202

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды