Fuji Xerox DocuPrint C2120 Скачать руководство пользователя страница 114 | Manualshive

Страница: 114 / 206

background image

114

6 Troubleshooting

Output is partially blank.
Vertical white streaks appear
on output.

The paper is not recommended for used with the printer. Load the correct paper.

Refer to

• "Supported Paper" (P. 71)

The paper is damp. Load new paper.

Toner cartridges are not installed correctly.
Correctly install them.

Dew condensation may have formed in the printer.
On the control panel, set the interval that the printer switches to the Sleep mode to
more than 60 minutes, and let the printer stand with its power on. After about an hour,
the condensation disappears due to the heat inside the printer.

Refer to

• "Sleep Mode Timer" (P. 91)

The Feed Roller Unit or Fuser Unit is damaged or old. Replace the Feed Roller Unit, the
Fuser Unit, or both. Contact our Customer Support Center or your dealers.

White patches appear on
output.
Toner scatters around images.
Images are bluish.

The image transfer voltage may not be set properly.
Correct the transfer voltage setting [Adjust BTR] on the control panel.

Refer to

• "7.10 Adjusting the Image Transfer Voltage" (P. 169)

Change the [Paper Type] setting and try printing again. For example, if [Paper Type] is
set to [Plain], try changing it to [Bond] or [Recycled]. If it is set to [Heavyweight 1], try
changing it to [Heavyweight 2].

Texts are smeared.

The paper is not recommended for used with the printer. Load the correct paper.

Refer to

• "Supported Paper" (P. 71)

The paper is damp. Load new paper.

Dew condensation may have formed in the printer.
On the control panel, set the interval that the printer switches to the Sleep mode to
more than 60 minutes, and let the printer stand with its power on. After about an hour,
the condensation disappears due to the heat inside the printer.

Refer to

• "Sleep Mode Timer" (P. 91)

Color around the edge of texts
is incorrect.

Color registration is incorrect.
Adjust the color registration on the control panel.

Refer to

• "7.9 Adjusting the Color Registration" (P. 165)

Symptom

Cause/Remedy

«
...
112
113
114
115
116
...
»

Содержание DocuPrint C2120















































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для DocuPrint C2120

Бренд: 3D Systems Страницы: 26

Бренд: 3D Systems Страницы: 39

WorkSeries 200 Series

Бренд: 3D Platform Страницы: 9

Бренд: TASKalfa Страницы: 36

Бренд: Radio Shack Страницы: 42

Бренд: Savin Страницы: 299

WorkCentre Pro 421

Бренд: Xerox Страницы: 162

Accel-a-Writer 8200

Бренд: Xante Страницы: 12

Бренд: aqprox! Страницы: 52

Бренд: Kimo Страницы: 2

Бренд: Oki Страницы: 174

Бренд: Oki Страницы: 9

Бренд: Aficio Страницы: 92

Бренд: Olivetti Страницы: 56

Бренд: QMS Страницы: 188

Бренд: Sinfonia Technology Страницы: 41

Бренд: Epson Страницы: 16

Бренд: Epson Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды