FEC Handheld Nutrunner HFC3000, Инструкция по эксплуатации

Страница: 44 / 231

Chapter 4 Installation and Wiring
PAGE 4-8
4-5-1 Controller I/O Signals
System parameter: SYS.033[xxx1xx] 0: 300ms/1: 800ms pulse length
Pin No. Signal IN/OUT Description of Function/Usage
TB3-1 IN COMMON IN Common input signal (bipolar)
TB3-2,11 +24V Service power
supply
0.5Amax
+24V output When using this power supply, keep wiring away from
electrical noise exposure. TB3-3,12 GND GND
TB1-1 STOP
IN-1(A:NO/
B:NC)
The fastening process
is stopped when this signal is set to “OFF.”
Selection between A contact and B contact type is possible.
System parameter: SYS.033[xx1xxx] 0: A contact/1: B contact
TB1-2 RESET IN-2(NO)
The fastening process is stopped and the fastening judgment of the
controller is cleared
when set “ON.” (ID data is cleared as well.)
TB1-3 REVERSE IN-3(NO)
The tool rotates in reverse
direction while “ON” and at the speed in
accordance with the selected WORK No. (Parameter)
TB1-4 START IN-4(NO)
When
“ON”, the fastening process is started in accordance with the
selected WORK No. (“Deadman” specification).
TB1-5 PROGRAM(BYPASS) IN-5(NO) The controller is put in the BYPASS (PROGRAM) mode when
“ON”.
TB1-6
SELF CHECK
DISABLE
IN-6(NO)
When set
“ON”, the self-check of the torque transducer (Zero Level /
Cal level voltage check) will not be performed (normally before the
start of the fastening operation - the start of tool rotation can be
shortened by approx. 60msec).
TB1-7 WORK SELECT BIT 0 IN-7(NO)
The WORK SELECT BIT 0
～
4 select signals enable selection
among parameter Nos. 1
～
32 by a (Binary) combination of the 5 pin
Nos. (See Work Select table further below)
TB1-8 WORK SELECT BIT 1 IN-8(NO)
TB1-9 WORK SELECT BIT 2 IN-9(NO)
TB1-10 WORK SELECT BIT 3 IN-10(NO)
TB1-11 WORK SELECT BIT 4 IN-11(NO)
TB1-12 BANK SELECT IN-12(NO) Bank select input signal (changes output signal definition)
TB3-4 OUT COMMON OUT Common output signal (bipolar)
TB3-5 BATCH OK RESET IN-13(NO) Cycle counter (ACCEPT count) reset signal
TB3-6 IN-14 NO Not USED
TB3-7 Bank Select Output OUT-6(NO) Output definition depends on status of Bank Select Input (TB1-12)
(See next page for output definition)
TB3-8 Bank Select Output OUT-7(NO)
TB3-9 Work Select Bit 5 IN-15 NO
The Work Select Bit 5 enables selection of parameters 33-64 in
combination with Work Select Bits 0-4 (Firmware Ver. 1.301 or later)
TB3-10 ID Work Select Enable IN-16 NO
Thw Work number selection by ID data input is enabled when ON.
(Firmware Ver. 1.301 or later)
TB2-1 Bank Select Output OUT-1(NO)
Output definition depends on status of Bank Select Input (TB1-12)
(See next page for output definition)
TB2-2
Bank Select Output
OUT-2(NO)
TB2-3
Bank Select Output
OUT-3(NO)
TB2-4
Bank Select Output
OUT-4(NO)
TB2-5 Bank Select Output OUT-5(NO)
TB2-6
Bank Select Output
OUT-12(NO)
TB2-7 MANREV (RY1-1) OUT-8(NO)
Turns ON when manually starting the reversed operation.
Turns OFF when the next fastening starts or turns OFF at RESET,
PROGRAM. (Relay contact-1)
TB2-8 BUZZER (RY2-1) OUT-9(NO)
Performs a duplication of the controller buzzer output of the REJECT
signal and Batch OK to external devices.
(Relay contact-2)
TB2-9
BATCH OK (RY3-1)
[TOTAL OK]
OUT-10(NO)
Output when the fastening results are OK for the programmed number
of cycles when using batch counting function (relay contact-3).
Selection between pulse or constant output is possible.
System parameter: SYS.033[xxxx1x] 0: constant 1: pulse
TB2-10 RY-COM(RY1,2,3-2) OUT Relay contact-1, 2, 3 common
TB2-11
TB2-12
QL OK (RY4-1)
[OK] (RY4-2)
OUT-11(NO)
OK output for QL Accept signal (relay contact) (Relay contact-4)
Selection between pulse and constant output is possible.
System parameter: SYS.033[xxxxx1] 0: constant 1: pulse