Fast 9500 Скачать руководство пользователя страница 84

Страница: 84 / 116

FILLING THE TANK

FILLING THE TANK

Boom Sprayer 9500 / 9600

Page 84

FILLING THE TANK

CAUTION: Prevent serious injury or

death.

Check chemical or fertilizer M/SDS for

proper handling instructions.

Toxic chemicals can enter the body by

breathing spray or contact with bare skin.

Do not take a chance with your health and

safety.

Filling the Product Tank

IMPORTANT: Transport the machine

with an EMPTY tank to prevent

machine damage.

CAUTION: Add only the amount of

liquid to the tank that is required for

the job.

NOTE: It is recommended that the

water supply system be equipped with

a pump for transferring water.

IMPORTANT: Be sure the water is

clean. Clean water is necessary to

prevent screen and check valve

plugging.

IMPORTANT: Do not start the sprayer

pump until the water from the supply

vehicle has started to flow. Water is

necessary to cool and lubricate the

pump seals. Without water, the seals

will fail in a few minutes.

Filling through the Top Lid

Figure 42: Top Lid

Place a water hose into the top lid,

start the pump on the supply vehicle,

and run it until the tank is filled to the

desired level.

Stop the pump, remove the hose, and

close the lid.

Do not run the

Sprayer

’

s pump until

the tank is at least 1/4-full of water.
Water is required in the pump to cool
its seals. A head of water is required
to keep the pump primed. Be sure the
booms are turned off.

Run in the circulate mode for at least

five minutes to thoroughly mix
(agitate) the solution before starting.

Filling through the Quick Fill

Figure 43: Quick Fill

Remove the fill line’s covers (A).

Connect a transfer hose to the

bottom fill line.

Open the fill line’s valve (B).

Содержание 9500





















































































































Результаты поиска

Содержание 9500

Отзывы:

Похожие инструкции для 9500

Бренды по названию

Популярные бренды

Fast 9500, Руководство пользователя

Результаты поиска

Содержание 9500

Отзывы:

Похожие инструкции для 9500

Бренды по названию

Популярные бренды