Fast 9500 Скачать руководство пользователя страница 73

Страница: 73 / 116

TRANSPORTING

TRANSPORTING

Boom Sprayer 9500 / 9600

Page 73

Transporting the Machine

Using Warning Lights

CAUTION: When transporting the

machine on a road or highway at night

or during the day, use accessory

lights and devices for adequate

warning to operators of other

vehicles. Check local governmental

regulations.

Various safety lights and devices are

available from Fast Ag Solutions dealer.

Keep safety items in good condition. Replace

missing or damaged items.

During periods of limited visibility, use pilot

vehicles and use extra lights on the machine.

During normal transport, both amber warning

lights will flash in unison at high intensity and

both red lamps will illuminate steadily at low

intensity.

When a turn is signaled, red and amber tail

lamps in the direction of turn will flash at high

intensity and in unison. On the opposite side,

amber and red lamps will illuminate steadily

at high intensity.

Keep Riders Off the Machine

Riders are subject to injury such as being

struck by foreign objects and being thrown off

the machine. Riders obstruct the Operator’s

view resulting in the machine being operated

in an unsafe manner.

Caution for All Machines

CAUTION: When transporting the

machine on a smooth surface road, do

not exceed the maximum transport

speed of 32 km/h (20 MPH). Reduce

speed considerably when traveling

over rough ground.

Reduce speed when turning. Do not

uncouple tractor brake pedals and apply

individually in an attempt to make a tighter

turn.

Serious injury or death can result from

contact with electric lines. Use care when

moving or operating this machine near

electric lines to avoid contact. Know

transport height and width of machine.

Check local regulations before transporting.

(See

Machine Dimensions & Specifications

for transport height and width of machine.)

Transport with wings fully folded. Never raise

or lower the center section or wings when

moving. After folding, ALWAYS place the fold

valve(s) in the neutral position for transport.

If wing-fold cylinders are removed or

damaged, chain wings together to prevent

injury or death caused by accidental falling of

wings on you or others.

. Rid

Содержание 9500





















































































































Результаты поиска

Содержание 9500

Отзывы:

Похожие инструкции для 9500

Бренды по названию

Популярные бренды

Fast 9500, Руководство пользователя

Результаты поиска

Содержание 9500

Отзывы:

Похожие инструкции для 9500

Бренды по названию

Популярные бренды