Fast 9500 Скачать руководство пользователя страница 103

Страница: 103 / 116

LUBRICATION & MAINTENANCE

LUBRICATION & MAINTENANCE

Boom Sprayer 9500 / 9600

Page 103

Cleaning

Filters

The fluid in the sprayer is continually being

filtered through a screen filter in the boom

control, agitation, and boom feed lines. The

sprayer must have clean water to prevent

clogging of the screens and check valves

when in use. These screens must be cleaned

daily or more often as required. To clean,

follow this procedure:

At the start of each day before the water

and chemicals are added, the screens

should be checked and cleaned.

If there is water or solution in the sprayer,

close the sump valve to isolate the

screens.

Loosen the filter bodies by hand. Do not

use a wrench as this could damage the

filter body.

Remove the screens and inspect them

for dirt.

Clean them using clean water.

Inspect for holes or tears. If there is

damage, replace it.

Install the screens and body to the filter

heads and tighten by hand. Do not use a

wrench as this might damage the body.

Do not over tighten and crack the head.

Open the ball valves to allow the solution

to circulate.

Drain all screens before storage to avoid

freezing.

Figure 50: Boom feed line filter

Figure 51: Typical boom line filter

Tank

WARNING: Do not enter the tank at

any time.

Daily

At the end of the working day, clean the

system using this procedure:

After the chemical solution has been

completely sprayed out through the

booms, add 20 gallons (75 liters)

clear water to the tank.

Run the agitation pump for 5 minutes.

Spray the rinse lightly over previously

sprayed crop.

Repeat Steps 1 - 3 with 30 gallons of

water.

Rinse the system again with clean

water.

Clean the screen and nozzles.

Drain the tank and let it dry.

To Remove Salt and Amines Formations

or Change Chemicals

Perform this cleaning cycle when changing

chemicals and/or annually.

Follow the procedure for

daily

cleaning

Remove all screens and nozzles and

wash them separately.

Add 50 gallons (200 liters) of clean

water to the tank.

Содержание 9500





















































































































Результаты поиска

Содержание 9500

Отзывы:

Похожие инструкции для 9500

Бренды по названию

Популярные бренды

Fast 9500, Руководство пользователя

Результаты поиска

Содержание 9500

Отзывы:

Похожие инструкции для 9500

Бренды по названию

Популярные бренды