Fast 9500 Скачать руководство пользователя страница 74

Страница: 74 / 116

TRANSPORTING

TRANSPORTING

Boom Sprayer 9500 / 9600

Page 74

Unfolding/Folding the Booms

Left Wing Tilt Switch

Main Wing Height Switch

Right Wing Tilt Switch

Main Wing Fold Switch

Flip Wings Fold Switch

Model specific

Figure 26: Transport Lock

Figure 27: Transport Pin

CAUTION: Be sure all bystanders are

clear of the Sprayer.

WARNING: Prevent serious injury or

death. The machine coming near or

contacting power lines can cause

electrocution. Electrocution can

occur without contact. Fully lower

wings before moving or transporting.

Place all controls in neutral, stop the

engine, set the parking brake, and

remove the ignition key before

proceeding.

Retract the transport lock pins from

their cradles.

Open the valve to the boom lift

cylinder(s) that allows the boom to

lower. Note that the valve might be

located on the hydraulic block for

some models.

Figure 28: Boom cylinder valve common to 60' - 100'

boom widths.

Start the tractor and run at 1/3-throttle

to provide hydraulic fluid to the boom

position cylinders.

See

Boom Function Control Box

for

per-switch functions.

Raise the booms above their cradles.

Содержание 9500





















































































































Результаты поиска

Содержание 9500

Отзывы:

Похожие инструкции для 9500

Бренды по названию

Популярные бренды

Fast 9500, Руководство пользователя

Результаты поиска

Содержание 9500

Отзывы:

Похожие инструкции для 9500

Бренды по названию

Популярные бренды