Fast 9500 Скачать руководство пользователя страница 72

Страница: 72 / 116

TRANSPORTING

TRANSPORTING

Boom Sprayer 9500 / 9600

Page 72

TRANSPORTING

Following

Safe

Transport

Procedures

Lights

SMV Emblem

Reflector Tape

Reflectors

CAUTION: When transporting the

machine on a road or highway at night

or during the day, use warning lights

and devices for adequate warning to

operators of other vehicles.

IMPORTANT: Transport Sprayer only

with tank EMPTY to prevent Sprayer

damage.

Check local governmental regulations.

Various safety devices are available from

your Fast Ag Solutions dealer. Keep safety

items in good condition. Replace missing or

damaged items.

Upward force on hitch may cause instability

when transporting. Add BALLAST to tractor

as required.

BEWARE of overhead wires and narrow

gates. KNOW the transport height and width

of your machine. (See

Machine Dimensions

& Specifications

Travel at a reasonable and safe speed;

REDUCE speed over rough or uneven

terrain, slopes, and when turning. See

Observe Maximum Transport Speed

BE SURE SMV emblem, reflectors, and

warning lights are clean, visible, and in good

condition.

BE SURE your safety chain has a strength

rating greater than the gross weight of the

machine.

Preparing the Machine for

Transport

CAUTION: See

Observe Maximum

Transport Speed

in the Safety section

for towing information.

CAUTION: Be sure all bystanders are

clear of the machine.

IMPORTANT: Transport Sprayer only

with tank EMPTY to prevent Sprayer

damage.

Transport Notes and Checks

Be sure that the Sprayer is properly

connected to the tractor. Always attach a

safety chain between the Sprayer and the

tractor and install a retainer through the

drawbar pin.

Ensure that the hitch/tongue latch is fully

engaged.

Install the Transport Locks & Pins over each

boom in its cradle before transporting.

Close the boom lift cylinder line valve.

Содержание 9500





















































































































Результаты поиска

Содержание 9500

Отзывы:

Похожие инструкции для 9500

Бренды по названию

Популярные бренды

Fast 9500, Руководство пользователя

Результаты поиска

Содержание 9500

Отзывы:

Похожие инструкции для 9500

Бренды по названию

Популярные бренды