Fast 9500 Скачать руководство пользователя страница 98

Страница: 98 / 116

LUBRICATION & MAINTENANCE

LUBRICATION & MAINTENANCE

Boom Sprayer 9500 / 9600

Page 98

LUBRICATION & MAINTENANCE

See these sections for component-specific

maintenance:

•

Tracks

Undercarriage Inspection and

Maintenance

•

Chemical Eductor

Maintenance

Lubricating and Maintaining the

Machine Safely

CAUTION: To help prevent serious

injury or death to you or others

caused by unexpected movement, be

sure to service machine on a level

surface.

If the machine is connected to a tractor,

engage the tractor’s parking brake, place the

tractor’s transmission in PARK, shut off the

engine, and remove its key. If the machine is

detached from the tractor, block wheels and

use safety stands to prevent movement.

Lubricant Storage

Equipment can operate at top efficiency only

when clean lubricants are used.

Use clean containers to handle all lubricants.

Whenever possible, store lubricants and

containers in an area protected from dust,

moisture, and other contamination. Store

containers on their side to avoid water and

dirt accumulation.

Make certain all containers are properly

marked to identify their contents.

Properly dispose of all old containers and

any residual lubricant they may contain.

Grease

Greases for Air Temperature Ranges

Use SAE multi-purpose high temperature

grease with extreme pressure performance

(EP) and is based on NLGI consistency

numbers and the expected air temperature

range during the service interval.

IMPORTANT: Some types of grease

thickeners are not compatible with

others. Consult your grease supplier

before mixing different types of

grease.

Alternative and Synthetic Lubricants

Conditions in certain geographical areas

may require lubricant recommendations

different from those printed in this Manual.

Synthetic lubricants may be used if they meet

the performance requirements as shown in

this Manual.

The temperature limits and service intervals

shown in this Manual apply to both

conventional and synthetic lubricants.

Содержание 9500





















































































































Результаты поиска

Содержание 9500

Отзывы:

Похожие инструкции для 9500

Бренды по названию

Популярные бренды

Fast 9500, Руководство пользователя

Результаты поиска

Содержание 9500

Отзывы:

Похожие инструкции для 9500

Бренды по названию

Популярные бренды