Fast 9500 Скачать руководство пользователя страница 89

Страница: 89 / 116

CHEMICAL EDUCTOR

CHEMICAL EDUCTOR

Boom Sprayer 9500 / 9600

Page 89

Maintenance

CAUTION: Divert or stop all flow to

and from the Cleanload™ system

before performing any service or

maintenance procedures.

CAUTION: Always wear proper

Personal Protective Equipment (PPE)

when handling chemicals, including

gloves, eye protection, a respirator,

and safety shoes.

CAUTION: Always dispose of

chemicals and contaminated water in

accordance with national and local

laws and statutes.

General Cleaning

Ensure that the components of the

Cleanload are free of any chemical buildup

or residue, both inside and out. Failing to

properly clean the system could lead to

reduced performance and component life.

Be sure to thoroughly clean the eductor, ball

valves and hopper. Cycle the ball valves

open and close during rinsing to ensure they

are clean.

Daily Maintenance

Always flush the Cleanload™ with clean

freshwater after each day’s use, if switching

chemicals, or if the system is going to be

inactive for an extended period.

Inspect all components for excessive wear,

leaks, or any other damage prior to each use.

Careful inspection is required before using

the system after long periods of inactivity.

Yearly Maintenance

Your Cleanload™ will last longer and give its

best performance when properly taken care

of. Proper Cleanload™ care depends on the

fluid or chemical being used and when the

Cleanload™ will be used again.

At the end of the spraying season, flush the

Cleanload™ with a neutralizing solution for

the fluid/chemical just used. Follow with a

clean freshwater rinse. This is especially

important for corrosive chemicals. Drain

Cleanload™ thoroughly, open all drain plugs,

and plug all ports until Cleanload™ is used

again.

If the system is to be stored in below freezing

ambient temperature (0°C, 32°F), flush the

Cleanload™ system with once with clean

freshwater and then again with antifreeze at

a dilution rate specified by the antifreeze’s

manufacturer.

Содержание 9500





















































































































Результаты поиска

Содержание 9500

Отзывы:

Похожие инструкции для 9500

Бренды по названию

Популярные бренды

Fast 9500, Руководство пользователя

Результаты поиска

Содержание 9500

Отзывы:

Похожие инструкции для 9500

Бренды по названию

Популярные бренды