Fast 9500 Скачать руководство пользователя страница 34

Страница: 34 / 116

SAFETY

SAFETY

Boom Sprayer 9500 / 9600

Page 34

Transport Safely

CAUTION: When transporting, always

travel at a reasonable and safe speed

which permits adequate control of

steering and stopping.

Reduce speed considerably when traveling

over rough ground. Be certain everyone is

clear of the machine.

Do not exceed weight and speed guidelines.

Refer to

Observe Maximum Transport

Speed

Towed loads can swerve and upset or cause

loss of control. Refer to

Tow Loads Safely

Shift tractor into a lower gear when

transporting down steep slopes or hills;

never coast. Stop slowly.

Wide turns may be required with the machine

in tow. Use caution in traffic and in congested

areas.

To improve stability when traveling through

the field, wings should be unfolded from

transport position as soon as possible after

leaving the roadway.

IMPORTANT: When transporting the

machine on a roadway, ALWAYS USE

appropriate lamps and devices for

adequate warning to operators of

other vehicles.

Refer to

Use Safety Lights and Devices

Park Safely

Parked Jack Position

Park the machine on a level surface, lower

the jack, and secure it. Block implement

wheels.

Содержание 9500





















































































































Результаты поиска

Содержание 9500

Отзывы:

Похожие инструкции для 9500

Бренды по названию

Популярные бренды

Fast 9500, Руководство пользователя

Результаты поиска

Содержание 9500

Отзывы:

Похожие инструкции для 9500

Бренды по названию

Популярные бренды