Fast 9500 Скачать руководство пользователя страница 79

Страница: 79 / 116

ADJUST GROUND SPEED

ADJUST GROUND SPEED

Boom Sprayer 9500 / 9600

Page 79

ADJUST GROUND SPEED

It will be necessary to establish a travel

speed and then set the flow to give the

desired application rate. Always run at the

established travel speed.

However, the best results are obtained when

the ground speed is 8 - 13 kph (5 - 8 mph).

See

Ground Speed Calibration

. Ground

speed variations in the field will automatically

be compensated.

Always operate at a comfortable speed. Do

not operate so quickly that the toolbar, trailer,

or tank bounces while going through the

field.

Effective results require that liquid be applied

at a consistent depth in a consistent manner.

Machine bouncing will prevent this required

consistency.

For broadcast spraying

Figure 41: Broadcast travel pattern

It is recommended that the operator makes

one pass around a field to start and then

spray back and forth to obtain the best

results. Using a marker system helps to

prevent skips or overlaps.

If your field has headlands, be sure to allow

sufficient space for turning.

For row crop spraying

Start at one edge of the field and go back and

forth until the field is completed.

Be sure the sprayer is calibrated, the nozzle

height and pressure are known, and the

tractor gear and RPM are determined before

starting to spray (see

SPRAYER

CALIBRATION

Proceed down the field at a constant speed.

Use the selected gear, engine RPM and

ground speed determined during the

calibration of the machine application rate.

Содержание 9500





















































































































Результаты поиска

Содержание 9500

Отзывы:

Похожие инструкции для 9500

Бренды по названию

Популярные бренды

Fast 9500, Руководство пользователя

Результаты поиска

Содержание 9500

Отзывы:

Похожие инструкции для 9500

Бренды по названию

Популярные бренды