Fast 9500 Скачать руководство пользователя страница 76

Страница: 76 / 116

HYDRAULIC FLOW

HYDRAULIC FLOW

Boom Sprayer 9500 / 9600

Page 76

HYDRAULIC FLOW

Regulating Hydraulic Flow to the

Pump

Locate your tractor model and follow the

appropriate setup instructions.

WARNING: FAILURE TO REGULATE

OIL FLOW WILL CAUSE MOTOR

FAILURE.

WARNING: NOT SUITABLE FOR

PUMPING FLAMMABLE LIQUIDS.

Load Sensing Closed Center System

(LS Closed)

Regulate oil flow with the tractor’s FLOW

CONTROL and FLOW LIMITER. (Do not use

restrictor orifice.)

Figure 33: Flow Limiter

Figure 34: Flow Control

Setup Instructions:

(Optional) Remove adapter and

install flow limiter in motor inlet port

(marked I).

Close motor needle valve: loosen jam

nut, screw needle valve clockwise

until seated, and lock jam nut (factory

setting.)

Shut off toolbar boom and agitation

valves if equipped.

Adjust tractor flow control to minimum

flow setting (Turtle).

Move

hydraulic

lever

“Lower/Retract” position to start

pump.

Adjust tractor flow control until the

toolbar shut-off (deadhead) pressure

is within the pump’s operating

parameters.

Note

: If the flow limiter

stops oil flow to the motor:

Move hydraulic lever to

“Float” or “Neutral” to remove

oil pressure from the flow

limiter.

Adjust tractor flow control to a

lower flow position.

Repeat steps 5 and 6.

Open the agitation valve(s).

Pressure Compensating Closed-

Center System (PC Closed)

Regulate oil flow by using a RESTRICTOR

ORIFICE. (Do not use flow limiter.)

Figure 35: Restrictor Orifice

Setup Instructions:

Install restrictor orifice by inserting

inside the adapter/restrictor body in

the motor inlet port (marked I).

Close motor needle valve: loosen jam

nut, screw needle valve clockwise

until seated, and lock jam nut (factory

setting.)

Set “Rabbit/Turtle” flow control to

“Turtle”.

Move hydraulic lever to the

“Lower/Retract” position to start

pump.

Adjust “Rabbit/Turtle” flow control

and agitation valve(s) to get desired

injection pressure.

Содержание 9500





















































































































Результаты поиска

Содержание 9500

Отзывы:

Похожие инструкции для 9500

Бренды по названию

Популярные бренды

Fast 9500, Руководство пользователя

Результаты поиска

Содержание 9500

Отзывы:

Похожие инструкции для 9500

Бренды по названию

Популярные бренды