Fast 9500 Скачать руководство пользователя страница 54

Страница: 54 / 116

CONTROLLER INSTALLATION

CONTROLLER INSTALLATION

Boom Sprayer 9500 / 9600

Page 54

CONTROLLER INSTALLATION

Each control box should be mounted in the

tractor cab.

Spray Circuit Controller

The control box is equipped with a "U"

bracket secured by knobs on each end of the

box. It provides a universal mounting system

adaptable to any configuration.

Use the two holes provided in the bracket to

mount the box to a solid surface. Position the

box to face the operator and tighten the

knobs to hold the box in position.

Cut the power cable to the required length.

Connect the white wire to ground and the red

wire to a 12-volt battery or power port. Refer

to Controller’s Manual. The panel fuse is an

AGC-15 amp.

IMPORTANT: Do not connect across a

24-volt system. It will damage internal

electrical components.

Boom Function Control Box

Mount the box next to the sprayer controller

to allow easy access. Connect to 12-volt

power port. The box’s fuse is an AGC-10

amp.

Plug the wiring harness from the trailer into

the plug on the pigtail that comes from the

Boom Function Control Box. Make sure to

properly index the connector.

Foam Marker Switch (Optional)

Mount the switch next to the Boom Function

Control Box to allow easy access for the

operator. Be sure to install the switch so that

moving to the left activates the left marker.

Connect the short wire to a 12-volt, 30-amp

power source. Secure with a strap, tape,

plastic ties, or a magnet.

Содержание 9500





















































































































Результаты поиска

Содержание 9500

Отзывы:

Похожие инструкции для 9500

Бренды по названию

Популярные бренды

Fast 9500, Руководство пользователя

Результаты поиска

Содержание 9500

Отзывы:

Похожие инструкции для 9500

Бренды по названию

Популярные бренды