Fast 9500 Скачать руководство пользователя страница 30

Страница: 30 / 116

SAFETY

SAFETY

Boom Sprayer 9500 / 9600

Page 30

immediately with soap and water. If chemical

gets into eyes, flush immediately with water.

Wash hands and face after using chemicals

and before eating, drinking, smoking, or

urination.

Do not smoke or eat while applying

chemicals.

After handling chemicals, always bathe or

shower and change clothes. Wash clothing

before wearing it again.

Seek medical attention immediately if illness

occurs during or shortly after use of

chemicals.

Keep chemicals in original containers. Do not

transfer chemicals to unmarked containers

or to containers used for food or drink.

Store chemicals in a secure, locked area

away from human or livestock food. Keep

children away.

Always dispose of containers properly. Triple

rinse empty containers and puncture or

crush containers and dispose of properly.

Handle Chemical Products Safely

Direct exposure to hazardous chemicals can

cause serious injury. Potentially hazardous

chemicals used with FAST equipment

include such items as lubricants, coolants,

paints, and adhesives.

A Material Safety Data Sheet (M/SDS)

provides specific details on chemical

products: physical and health hazards,

safety procedures, and emergency response

techniques.

Check the M/SDS before you start any job

using a hazardous chemical. That way you

will know exactly what the risks are and how

to do the job safely. Then follow the

procedures

with

the

recommended

equipment.

Operate Hydraulics Safely

Before operating, make sure air has been

bled from wing-fold hydraulic system.

Be sure the area around the machine is clear

before raising or lowering the machine’s

frame or wings.

Do not operate with wings folded.

Do not operate close to the edge of a ditch,

creek, gully, or steep embankment. Avoid

holes, ditches, and obstructions which may

cause the tractor, machine, or towed

equipment to roll over, especially on hillsides.

Avoid sharp turns on hillsides.

Slow down when turning, traveling over

rough ground, or when turning on inclines.

Always shut off tractor and shift to PARK or

set brakes when leaving tractor. Remove key

when leaving tractor unattended.

Always have the tractor stop on level ground

when raising or lowering wings. Operate the

machine from tractor seat only. If chemicals

are used, follow the manufacturer’s

recommendations for handling and storage.

Tow the machine behind a properly equipped

tractor only.

Содержание 9500





















































































































Результаты поиска

Содержание 9500

Отзывы:

Похожие инструкции для 9500

Бренды по названию

Популярные бренды

Fast 9500, Руководство пользователя

Результаты поиска

Содержание 9500

Отзывы:

Похожие инструкции для 9500

Бренды по названию

Популярные бренды