Fast 9500 Скачать руководство пользователя страница 48

Страница: 48 / 116

PREPARING THE MACHINE

PREPARING THE MACHINE

Boom Sprayer 9500 / 9600

Page 48

PREPARING THE MACHINE

Use the Tractor Operator’s Manual

Always refer to tractor operator's manual for specific detailed information regarding operation of

equipment.

Pre-Operation Checklist

Efficient and safe operation of the machine requires that each Operator reads and understands

operating procedures and all related safety precautions outlined in this section. A pre-operational

checklist is provided for the Operator. It is important for both personal safety and maintaining the

good mechanical condition of the Sprayer that this checklist be followed.

Before operating the Sprayer, check the following items:

Lubricate machine per the schedule outlined in the

LUBRICATION and

MAINTENANCE

section.

Use only a tractor of adequate power and weight to operate the Sprayer. See the

SPECIFICATIONS

section for recommendations.

Be sure that the machine is properly attached to the tractor. Be sure that a mechanical

retainer is installed through the drawbar and that a pin and safety chain are installed.

Inspect all hydraulic lines, hoses, fittings, and couplers for tightness. See

Tightening

Hardware

for break-in period recommendations.

IMPORTANT

: Extend the axles out of the shipping width setting and set the track or

tire width for your application. The unit is shipped with axles to the narrowest setting

using the shipping holes for shipping purposes only. See

SETTING AXLE WIDTH

Check tires and verify they are inflated to the specified pressure. See

Checking Tire

Pressure

Check track tension and hardware torque (if applicable).

Calibrate the Sprayer if at the start of the season or a new applicator rate is being

used.

Check that all connections in the electrical system are connected and tight.

10.

Check the condition and routing of all fluid hoses and lines. Be sure that all lines are

routed in large arcs. Replace any that are damaged. Re-route those that are rubbed,

pinched, or crimped. See

Replace Hydraulic Hoses

11.

Check the spray pattern of each nozzle. Remove and clean or replace any that have

an unusual pattern.

12.

Remove the line filters, wash them with clean water, and reinstall them.

13.

Remove all entangled material.

Содержание 9500





















































































































Результаты поиска

Содержание 9500

Отзывы:

Похожие инструкции для 9500

Бренды по названию

Популярные бренды

Fast 9500, Руководство пользователя

Результаты поиска

Содержание 9500

Отзывы:

Похожие инструкции для 9500

Бренды по названию

Популярные бренды