Fagor CNC 8060, Руководство по установке, Страница: 22 / 698

Installation manual.
CNC 8060
CNC 8065
·22·
(R
EF
: 1709)
Ref. 1505
Position (machine coordinates) calculated for the rotary axis of the kinematics
at the beginning of the block, for solution 2 of the #CSROT mode. • Variables: (V.)G.CSROTF2[1]
(V.)G.CSROTS2[1]
(V.)G.CSROTT2[1]
(V.)G.CSROTO2[1]
Position (machine coordinates) calculated for the rotary axis of the kinematics
at the end of the block, for solution 2 of the #CSROT mode. • Variables: (V.)G.CSROTF2[2]
(V.)G.CSROTS2[2]
(V.)G.CSROTT2[2]
(V.)G.CSROTO2[2]
Position (machine coordinates) to be occupied by the rotary axis of the
kinematics at the beginning of the block, for the #CSROT mode. • Variables: (V.)G.CSROTF[1]
(V.)G.CSROTS[1]
(V.)G.CSROTT[1]
(V.)G.CSROTO[1]
Position (machine coordinates) to be occupied by the rotary axis of the
kinematics at the end of the block, for the #CSROT mode. • Variables: (V.)G.CSROTF[2]
(V.)G.CSROTS[2]
(V.)G.CSROTT[2]
(V.)G.CSROTO[2]
Position of the part zero transformed by the instruction #KINORG, considering
the table position, on the first three axes of the channel. • Variable: (V.)G.KINORG1
(V.)G.KINORG2
(V.)G.KINORG3
Software V01.10.03
Enable tool withdrawal (retraction) in threading. • Machine parameter: RETRACTTHREAD.
• PLC marks: RETRACT.
Assume IPLANE as active plane after M30/RESET or keep the active one. • Machine parameter: PLANECANCEL.
Detailed CNC status in automatic mode. New value $100000. • Variable: (V.)G.CNCAUTSTATUS
Volts of the local analog output [n] (only at the 8060). • Variable: (V.)G.ANALO[n]
Volts of output [n] of the RCS-S module. • Variable: (V.)G.ANASO[n]
Withdraw the axes after interrupting an electronic threading. • Variable: (V.)G.RETREJ
Software V01.30
New language (dutch). • Machine parameter: LANGUAGE.
Multi-axis management. The deactivated axis maintains its coordinate
regardless of the active axis. • Machine parameter: KEEPPOS.
Define the feedback type of the handwheel connected to the local feedback. • Machine parameter: HWFBTYPE.
Define the feedback type of the axis connected to the local feedback. • Machine parameter: FEEDBACKTYPE.
HSC. Orientation smoothing of the rotary axes working with RTCP. • Machine parameter: ORISMOOTH.
If the [ESC] key is configured as "Previous component", it does not change
the main component (Main Menu). • Machine parameter: FUNCTION.
Maximum frequency recommended for SSI communication, depending on
cable length. • Machine parameter: SSICLKFREQ.
The SPDLEREV mark (reverse turning direction in M19) also affects the
velocity-Sercos spindles. • Machine parameter: M19SPDLEREV.
Kinematics (types 9 through 12). Origin for applying the RTCP. • Machine parameter: TDATA7.
Kinematics (types 13 through 16). Origin for applying the RTCP. • Machine parameter: TDATA7.
Variables related to the position of the axes.
• Distance left (to go) for the axis to reach the programmed coordinate. • Variable: (V.)A.TOGO.xn
Variables related to functions.
• System spindles involved in the subroutine associated with M3, M4, M5,
M19 and M41-M44.
• Variable: (V.)G.SUBMSPDL
Variables related to canned cycles.
• Active canned cycle. • Variable: (V.)G.ACTIVECYLE
Variables related to the probe.
• Status of probe ·1·.
• Probing movement. Value measured at the master spindle of the channel.
• Variable: (V.)G.PRBST
• Variable: (V.)G.PLMEAS4
Variables related to axis and spindle repositioning.
• End of axis and spindle repositioning at the starting point.
• End of axis and spindle repositioning at the interruption point.
• Variable: (V.)G.ENDREPINI
• Variable: (V.)G.ENDREPINT
Variables related to synchronized switching.
• Time remaining to activate the laser output.
• Time remaining to deactivate the laser output.
• Variable: (V.)G.LASEROTMON
• Variable: (V.)G.LASEROTMOFF
PWM related variables
• Amount of time that PWM stays active in burst mode.
• Final PWM status once burst mode is over.
• Variable: (V.)G.PWMBTIME
• Variable: (V.)G.PWMBEND
Variables related to cycle time.
• Percentage of loop time (cycle time) used by the PLC.
• Percentage of loop time (cycle time) used by the dynamic preparation of
the tool path.
• Variable: (V.)G.PLCTIMERATE
• Variable: (V.)G.TRAYTIMERATE
Variables related to the feedback inputs.
• Value of the local count-up 1 input.
• Value of the local count-up 2 input.
• Variable: (V.)G.LCOUNTER1
• Variable: (V.)G.LCOUNTER2
Feedrate related variables.
• Actual (real) CNC feedrate in G95.
• Real feedrate on the tool path.
• Feedrate active in the block.
• Variable: (V.)G.FREALPR
• Variable: (V.)G.ACTFEED
• Variable: (V.)G.IPOFEED
Variables related to the active tool and to the next one.
• Active tool. Code of the tool offset type. • Variable: (V.)TM.TOOLTYP[ofd]
Software V01.10