Ericsson AVP 4000 Скачать руководство пользователя страница 91

Страница: 91 / 422

Getting Started

1/1553-FGC 101 1790 Uen Y

3-55

MGP is configured automatically by Ericsson control software, but can be set up via

the GUI (or the Front Panel). Please note that some of the settings mentioned here

are hidden if the unit is or has been under the control of Ericsson control software.

MGP can operate in one of two modes, or it may be turned off:

•

Unit Level

mode, it is assumed that another unit is, or may be configured

with, the same output transport streams. When a failure occurs, MGP will

coordinate a redundancy switch of all the services from one unit to the other.

•

Media Level

mode, transport streams may be grouped together into media

bundles, which may be individually switched between units.

In addition, MGP operation is significantly affected by two other settings:

•

The Network Mode for the output Interfaces, a choice of

Same Network

Different Network

, and

•

The transport stream source IP redundancy, a choice of

Transparent

Non-

transparent

With a

Network Mode

set to

Same-Network

, interfaces 3 and 4 share the same IP

address and are therefore on the same network. Further options define how the

interfaces are used. But from the perspective of MGP, there is only one logical

output interface.

With a

Network Mode

set to

Different-Network

, interfaces 3 and 4 must be

connected to seemingly different networks (or sub nets) and they each get their own

distinct IP address.

When

TS Source IP Redundancy

is set to

Transparent

, media IP packets and

MGP status IP packets are virtually sourced from IP addresses which can remain

the same when a service bundle is switched from one unit to another. This setting is

incompatible with the

Different-Network

mode.

MGP works by emitting MGP Status Messages (MSMs) alongside the media

packets, but on a separate multicast common to a bundle, if applicable, and shared

with units likely to take over a service in case of failure or simply targeted for a near-

seamless switch.

3.7.22.2

Configuring MGP

Set up the output interface Network mode:

Device Configuration > Advanced

Setup > Device > Network Configuration > Data Interface Group 3-4 >

Network Mode

1. Set up the Transport Stream source IP redundancy mode:

Device

Configuration > Advanced Setup > Device > Base Unit > TS Source IP

Redundancy

Note:

A selection of output interface Network mode of

Different Network

together with a transport stream source IP redundancy mode of

Transparent

, is not a valid combination.

Содержание AVP 4000







































































































































































































































































































































































































































Результаты поиска

Содержание AVP 4000

Отзывы:

Ericsson AVP 4000, Справочное руководство, Страница: 91 / 422

Результаты поиска

Содержание AVP 4000

Отзывы: