manualshive.com logo in svg

Ericsson AVP 4000, Справочное руководство, Страница: 158 / 422

Поделиться
Скачать
Ericsson AVP 4000 Скачать руководство пользователя страница 158

 

 

Front Panel Control  

 

4-18 

 

1/1553-FGC 101 1790 Uen Y

  

 

 

 

received in a time divided manner (Half Duplex) or transmission and reception can 

happen at the same time over the same link (Full Duplex). Auto is for automatic 

configuration. 

 

 

 

Default MAC Address 

Virtual MAC address assigned to the Control Interface Group. 

 

 

 

IP Address 

The IP address associated with the interface group. 

 

 

 

Subnet Mask 

The subnet mask associated with the interface group. 

 

 

 

Gateway Address 

The gateway address associated with the interface group. 

 

 

 

IGMP Mode Selection 

IGMPv2/IGMPv3. Internet Group Management Protocol selection. 

 

 

 

Physical Control Port <n> 

The physical control port labelled as Ge <n> of the current control interface group. 

 

 

 

 

Default MAC Address 

The hardware address of the Ge <n> interface. 

 

 

 

 

Link Status 

Link Down, Link Up. The status of the current physical data interface. 

 

 

 

 

Link Up Time 

The time in days, hours, minutes and seconds the link is established. Read only 

parameter. 

 

 

 

 

TX Packets 

The packets transmitted since the link is up. 

 

 

 

 

RX Packets 

The packets received since the link is up. 

 

 

 

 

IP Address 

The IP address of the physical data interface. 

 

 

Data Interface Group <n> 

 

 

 

 

Network Mode 

Same-Network, Different-Network. If set to Different-Network, the two ports in the group 

can belong to different subnets. In Different-Network mode only the Active-Active 

Redundancy mode is supported. 

 

 

 

IP Redundancy Mode 

Active-Active, Active-Standby. Describes how the spare interfaces will behave. For a 

data interface group only Active/Active is supported. 

 

 

 

Autorevert 

Auto-revert to Primary, Auto-revert to Secondary. Shown only if the IP Redundancy 

mode is set to Active-Standby. Determines what to do when connection is lost. 

 

 

 

Autorevert Delay 

The delay in seconds before automatic redundancy switching takes place. Shown only if 

the 

IP Redundancy mode

 is set to Active-Standby. 

 

 

 

Active Interface 

Read only parameter. Displays which interface is active. In Active -Active redundancy 

mode both interfaces are active. 

 

 

 

Line Speed 

Auto, 100 Mpbs, 1 Gbps. The transmission speed of the link. 

 

 

 

Duplex Mode 

Auto, Full Duplex, Half Duplex. Determines whether data should be transmitted and 

received in a time divided manner (Half Duplex) or transmission and reception can 

happen at the same time over the same link (Full Duplex). Auto is for automatic 

configuration. 

 

 

 

Default Virtual MAC Address 

Virtual MAC address assigned to the current Data Interface Group. 

 

 

 

IP Address 

The IP address associated with the interface group. 

 

 

 

Subnet Mask 

The subnet mask associated with the interface group. 

 

 

 

Gateway Address 

The gateway address associated with the interface group. 

 

 

 

IGMP Mode Selection 

IGMPv2/IGMPv3. Internet Group Management Protocol selection. 

 

 

 

Physical Data Interface <m> 

The physical data interface labelled as Ge <m> of the current data interface group. 

 

 

 

 

Default MAC Address 

The hardware address of the Ge <n> interface. 

Содержание AVP 4000







































































































































































































































































































































































































































Отзывы:

Нет отзывов