Ericsson AVP 4000 Скачать руководство пользователя страница 46

Страница: 46 / 422

Getting Started

3-10

1/1553-FGC 101 1790 Uen Y

3.5

How to Configure Ethernet Control Ports

Overview

The Base Chassis has two Ethernet control ports that support IEEE 802.3

100BaseTX and 1000BaseT protocols. The control ports are accessible via RJ-45

connectors mounted on the rear panel of the unit.

Figure 3.2 Ethernet Control Port Numbering

The Ethernet control ports are used to connect the unit to a control computer for

control through a web browser or to a control system for control through nCompass

Control (V6.5 onwards).

Ethernet Control Port Parameters

A single IP port is defined for all Ethernet control traffic to and from the chassis. The

physical ports used for Ethernet control are by default the control Ethernet ports.

The control ports can raise an alarm during abnormal operational conditions.

The parameters controlling Ethernet port are as shown in the following table.

Table 3.2 Ethernet Control Port Parameters

Parameter

Values

Description

Comments

Network Mode

Same Network

The interface pair is on the same

subnet.

Read only parameter

Different Network

The interface pair is on different

subnet.

IP Redundancy Mode

Active-Active

The same traffic is present on both

interfaces all the time.

Read only parameter.

Active-Standby

The secondary interface is active

only if the primary is down.

Autorevert

Auto-revert to Primary

Enables auto-revert mode on the

interface group.

Auto-revert to Secondary

Autorevert delay

The time taken to enable an

interface participate in redundancy,

after the interface link is up. If this is

set to 0 then switching happens

immediately.

Содержание AVP 4000







































































































































































































































































































































































































































Результаты поиска

Содержание AVP 4000

Отзывы:

Ericsson AVP 4000, Справочное руководство, Страница: 46 / 422

Результаты поиска

Содержание AVP 4000

Отзывы: