Ericsson AVP 4000 Скачать руководство пользователя страница 249

Страница: 249 / 422

Web GUI Control

1/1553-FGC 101 1790

Uen

5-65

Parameter

Values

Description

AFD Sustain

Maintain previously received AFD code

indefinitely
Maintain previously received AFD code for

period specified in Sustain Timeout, then drop to

default, i.e. code 1000

Maintain previously received AFD code for

period specified in Sustain Timeout, then switch

AFD off

Control what AFD code goes out when AFD is lost at input.
Indefinitely: Maintains previously received AFD code

indefinitely.
Default after Timeout: Maintains previously received AFD

code for period specified in Sustain Timeout, then drop to

default, i.e. code 1000.
Off after Timeout: Maintains previously received AFD code

for period specified in Sustain Timeout, then switch AFD

off.

AFD Sustain Timeout

0 to 5,10, 20, 50, 100, 120

Control how long in frames previous AFD code is

maintained. Zero means drop to default immediately on

loss.

Input Detection

The CE-HEVC VCM supports video input detection as described in

Chapter 3,

Getting Started: How to Configure and Use Input Detection

, with the exception of

"Auto Detect and Restore Saved Config".

5.5.3.2.2

Audio Stream Configuration

Audio Input

The following parameters are available on the

Input

tab of the

Properties

widget on

the

Service Configuration

page when an audio component is selected in the

Outputs

widget. The same parameters can be accessed through the

Advanced/CE-HEVC/Audio Module/Audio <n>/Input

menu on the front panel.

Table 5.42 Audio Input Parameters

Parameter

Values

Description

Input Format

Uncompressed (LPCM), MPEG Layer II, Dolby

Digital, Dolby E, AAC

Sets the input format used by the audio encoder.

Input Source

Off, Mute, Test Tone, Embedded 1 to 8, Input 1 -

Sets the source used by the audio encoder. No input is fed

to the encoder if Off is selected. Mute mutes the incoming

audio and encodes silence. Test Tone encodes an 1 kHz

test tone, Embedded 1 to 8 sets the source to an SDI

embedded audio stream. Input 1-4 are for the digital

inputs.

Output On Audio Loss

No PID, Silence

Specifies the action to take when input is Lost. No PID is

for dropping the audio PID from the stream, Silence is for

encode silence.
NOTE: When No PID is selected, the reference to the PID

is not removed from the Program Map Table, so a

Transport Stream analyzer will indicate a ghost PID in the

output Transport Stream.

Source Switchout

Off, Mute, Test Tone, Embedded 1 to 8, Input 1 -

Specifies which input to output to the reference output on

the 15-way D-type audio connector.

Содержание AVP 4000







































































































































































































































































































































































































































Результаты поиска

Содержание AVP 4000

Отзывы:

Ericsson AVP 4000, Справочное руководство, Страница: 249 / 422

Результаты поиска

Содержание AVP 4000

Отзывы: