Ericsson AVP 4000 Скачать руководство пользователя страница 336

Страница: 336 / 422

Preventive Maintenance and Fault-finding

8-16

1/1553-FGC 101 1790 Uen Y

There is no status of the Generic ANC input carried over SMPTE 2038 output: bit

rate or ANC content. However, there is an alarm if the incoming ANC (excluding

audio) exceeds the bit rate set by the user. In this case, the ANC output will be

dropped to avoid exceeding the maximum user bit rate and thus avoiding corrupting

other components in the Transport Stream.

8.5.9

Reflex and Seamless Operation Problems

8.5.9.1

Internal Reflex Automatic Settings Problems

Different video formats in the same internal Reflex group may cause range issues

when the Reflex setting is set to automatic mode. In this case, we recommend using

the manual settings and using the recommended settings listed in

Chapter 3,

Getting Started

If problems are observed with Reflex in automatic mode, the following Reflex HD

MPEG-2 manual mode settings are recommended: Bmin = 3 Mbps, Bmax =

20 Mbps, Buffer Delay = 2.6 seconds.

8.5.9.2

Seamless Mode Parameter Restrictions

When the buffer mode is set to

Seamless

, the configuration of the encoder buffer

size (VBV buffer in MPEG-2, CPB buffer in H.264) is set by the user using the

following parameters:

•

Buffer Delay between 500 ms to 7000 ms (

Seamless Buffer Delay

)

•

Min Seamless Bitrate (Bmin)

•

Buffer Size = Bmin x Buffer Delay

In seamless mode, restrictions in

Bmin

and

seamless delay

are in place to force a

reasonable encoding buffer size and avoids it to be to low

If the

seamless delay

and

Bmin

are set too low, the

Bmin

range will change so

that the buffer size (Bmin x Delay) remains above 1 Mbit in SD and 3 Mbit in HD.

For example, in SD if the buffer delay is set to 500 ms, the lowest allowable

Bmin

2 Mbps. in HD, a buffer delay of 1000 ms will not allow any

Bmin

to be set below

3 Mbps.

8.5.9.3

Seamless Mode parameter results in a buffer size out of specification

Although you are prevented from setting

Bmin

and

Delay

to values that will result in

a small buffer size, there are NO restriction on the maximum value of the resulted

buffer size.

To ensure the buffer is compliant to the specifications, ensure that the buffer size is

limited to the MPEG-2 or H.264 specifications.

Buffer Size = Bmin x Buffer Delay

Содержание AVP 4000







































































































































































































































































































































































































































Результаты поиска

Содержание AVP 4000

Отзывы:

Ericsson AVP 4000, Справочное руководство, Страница: 336 / 422

Результаты поиска

Содержание AVP 4000

Отзывы: