Endress+Hauser Proline Promag 300 Скачать руководство пользователя страница 132

Страница: 132 / 272

Description of device parameters

Proline Promag 300 Modbus RS485

132

Hauser

Switch out funct



Navigation

 Expert → Output → PFS output 1 to n → Switch out funct (0481–1 to n)

Prerequisite

The

Switch

option is selected in the

Operating mode

parameter (→  120).

Description

Use this function to select a function for the switch output.

Selection

• Off

• On

• Diag. behavior

• Limit

• Fl. direct.check

• Status

Factory setting

Off

Additional information

Selection

• Off

The switch output is permanently switched off (open, non-conductive).

• On

The switch output is permanently switched on (closed, conductive).

• Diag. behavior

Indicates if the diagnostic event is present or not. Is used to output diagnostic

information and to react to it appropriately at the system level.

• Limit

Indicates if a specified limit value has been reached for the process variable. Is used to

output diagnostic information relating to the process and to react to it appropriately at

the system level.

• Fl. direct.check

Indicates the flow direction (forward or reverse flow).

• Status

Indicates the device status depending on whether empty pipe detection or low flow cut

off is selected.

Assign diag. beh



Navigation

 Expert → Output → PFS output 1 to n → Assign diag. beh (0482–1 to n)

Prerequisite

• In the

Operating mode

parameter (→  120), the

Switch

option is selected.

• In the

Switch out funct

parameter (→  132), the

Diag. behavior

option is selected.

Description

Use this function to select the diagnostic event category that is displayed for the switch

output.

Selection

• Alarm

• Alarm or warning

• Warning

Factory setting

Alarm

Содержание Proline Promag 300

















































































































































































































































































Результаты поиска

Содержание Proline Promag 300

Отзывы:

Похожие инструкции для Proline Promag 300

Бренды по названию

Популярные бренды

Endress+Hauser Proline Promag 300, Описание параметров устройства

Результаты поиска

Содержание Proline Promag 300

Отзывы:

Похожие инструкции для Proline Promag 300

Бренды по названию

Популярные бренды