Endress+Hauser Proline Promag 300 Скачать руководство пользователя страница 97

Страница: 97 / 272

Proline Promag 300 Modbus RS485

Description of device parameters

Hauser

Apply I/O config (3907)

→  98

Alteration code (2762)

→  98

I/O 1 to n terminals

Navigation

 Expert → I/O config. → I/O 1 to n terminals (3902–1 to n)

Description

Displays the terminal numbers used by the I/O module.

User interface

• Not used

• 26-27 (I/O 1)

• 24-25 (I/O 2)

• 22-23 (I/O 3)

I/O 1 to n info

Navigation

 Expert → I/O config. → I/O 1 to n info (3906–1 to n)

Description

Displays information about the plugged in I/O module.

User interface

• Not plugged

• Invalid

• Not configurable

• Configurable

• MODBUS

Additional information

"Not plugged" option

The I/O module is not plugged in.

"Invalid" option

The I/O module is not plugged correctly.

"Not configurable" option

The I/O module is not configurable.

"Configurable" option

The I/O module is configurable.

"Fieldbus" option

The I/O module is configured for the fieldbus.

Содержание Proline Promag 300

















































































































































































































































































Результаты поиска

Содержание Proline Promag 300

Отзывы:

Похожие инструкции для Proline Promag 300

Бренды по названию

Популярные бренды

Endress+Hauser Proline Promag 300, Описание параметров устройства

Результаты поиска

Содержание Proline Promag 300

Отзывы:

Похожие инструкции для Proline Promag 300

Бренды по названию

Популярные бренды