Endress+Hauser Proline Promag 300 Скачать руководство пользователя страница 201

Страница: 201 / 272

Proline Promag 300 Modbus RS485

Description of device parameters

Hauser

201

Maximum value

Navigation

 Expert → Diagnostics → Min/max val. → Temperature → Maximum value (6680)

Prerequisite

One of the following conditions is met:

• Order code for "Sensor option", option

"Medium temperature measurement"

• The temperature is read into the flowmeter from an external device.

Description

Displays the highest previously measured medium temperature value.

User interface

Signed floating-point number

Additional information

Dependency

The unit is taken from the

Temperature unit

parameter (→  58)

3.8.13 "Heartbeat" submenu

For detailed information on the parameter descriptions for the

Heartbeat

VerifMonitoring

application package, refer to the Special Documentation for

the device →  7

Navigation

 Expert → Diagnostics → Heartbeat

‣

Heartbeat

‣

Base settings

‣

Perform.verific.

‣

Verific. results

‣

Monitor. results

3.8.14 "Simulation" submenu

Navigation

 Expert → Diagnostics → Simulation

‣

Simulation

Assign proc.var. (1810)

→  202

Proc. var. value (1811)

→  203

Status inp. sim. (1355)

→  203

Содержание Proline Promag 300

















































































































































































































































































Результаты поиска

Содержание Proline Promag 300

Отзывы:

Похожие инструкции для Proline Promag 300

Бренды по названию

Популярные бренды

Endress+Hauser Proline Promag 300, Описание параметров устройства

Результаты поиска

Содержание Proline Promag 300

Отзывы:

Похожие инструкции для Proline Promag 300

Бренды по названию

Популярные бренды