Endress+Hauser Proline Promag 300 Скачать руководство пользователя страница 139

Страница: 139 / 272

Proline Promag 300 Modbus RS485

Description of device parameters

Hauser

139

Assign limit

Assign diag. beh

Assign status

Switch-off value

Switch-off delay

Switch-on value

Switch-on delay

Failure mode

Switch status

Powerless relay

Terminal no.

Navigation

 Expert → Output → Relay output 1 to n → Terminal no. (0812–1 to n)

Description

Displays the terminal numbers used by the relay output module.

User interface

• Not used

• 24-25 (I/O 2)

• 22-23 (I/O 3)

Additional information

"Not used" option

The relay output module does not use any terminal numbers.

Relay outp.func.



Navigation

 Expert → Output → Relay output 1 to n → Relay outp.func. (0804–1 to n)

Description

Use this function to select an output function for the relay output.

Selection

• Closed

• Open

• Diag. behavior

• Limit

• Fl. direct.check

• Digital Output

Содержание Proline Promag 300

















































































































































































































































































Результаты поиска

Содержание Proline Promag 300

Отзывы:

Похожие инструкции для Proline Promag 300

Бренды по названию

Популярные бренды

Endress+Hauser Proline Promag 300, Описание параметров устройства

Результаты поиска

Содержание Proline Promag 300

Отзывы:

Похожие инструкции для Proline Promag 300

Бренды по названию

Популярные бренды