Endress+Hauser Proline Promag 300 Скачать руководство пользователя страница 35

Страница: 35 / 272

Proline Promag 300 Modbus RS485

Description of device parameters

Hauser

Diagnostic no. 442 (Freq. output 1 to n)



Navigation

 Expert → System → Diagn. handling → Diagn. behavior → Diagnostic no. 442 (0658)

Prerequisite

The measuring device has a pulse/frequency/switch output.

Description

Use this function to change the diagnostic behavior of the diagnostic message

442 Freq.

output 1 to n

Selection

• Off

• Alarm

• Warning

• Logbook only

Factory setting

Warning

Additional information

For a detailed description of the options available, see →  32

Diagnostic no. 443 (Pulse output 1 to n)



Navigation

 Expert → System → Diagn. handling → Diagn. behavior → Diagnostic no. 443 (0659)

Prerequisite

The measuring device has a pulse/frequency/switch output.

Description

Use this function to change the diagnostic behavior of the diagnostic message

443 Pulse

output 1 to n

Selection

• Off

• Alarm

• Warning

• Logbook only

Factory setting

Warning

Additional information

For a detailed description of the options available, see →  32

Diagnostic no. 444 (Current input 1 to n)



Navigation

 Expert → System → Diagn. handling → Diagn. behavior → Diagnostic no. 444 (0740)

Prerequisite

The device has one current input.

Description

Use this function to change the diagnostic behavior of the diagnostic message

444 Current input 1 to n

Содержание Proline Promag 300

















































































































































































































































































Результаты поиска

Содержание Proline Promag 300

Отзывы:

Похожие инструкции для Proline Promag 300

Бренды по названию

Популярные бренды

Endress+Hauser Proline Promag 300, Описание параметров устройства

Результаты поиска

Содержание Proline Promag 300

Отзывы:

Похожие инструкции для Proline Promag 300

Бренды по названию

Популярные бренды