Endress+Hauser Proline Promag 300 Скачать руководство пользователя страница 171

Страница: 171 / 272

Proline Promag 300 Modbus RS485

Description of device parameters

Hauser

171

Additional information

Description

This setting does not affect the failsafe mode of other totalizers and the outputs. This

is specified in separate parameters.

Selection

• Stop

The totalizer is stopped in the event of a device alarm.

• Actual value

The totalizer continues to count based on the actual measured value; the device alarm is

ignored.

• Last valid value

The totalizer continues to count based on the last valid measured value before the device

alarm occurred.

3.7.2

"Custody transfer" submenu

Only available for Promag H.

For detailed information on the parameter descriptions for custody transfer

measurement, see the Special Documentation for the device →  7

Navigation

 Expert → Application → Custody transfer

‣

Custody transfer

3.8

"Diagnostics" submenu

Navigation

 Expert → Diagnostics

‣

Diagnostics

Actual diagnos. (0691)

→  172

Prev.diagnostics (0690)

→  173

Time fr. restart (0653)

→  174

Operating time (0652)

→  174

‣

Diagnostic list

→  174

‣

Event logbook

→  179

‣

Cust.transf.log.

→  181

‣

Device info

→  181

Содержание Proline Promag 300

















































































































































































































































































Результаты поиска

Содержание Proline Promag 300

Отзывы:

Похожие инструкции для Proline Promag 300

Бренды по названию

Популярные бренды

Endress+Hauser Proline Promag 300, Описание параметров устройства

Результаты поиска

Содержание Proline Promag 300

Отзывы:

Похожие инструкции для Proline Promag 300

Бренды по названию

Популярные бренды