Endress+Hauser Proline Promag 300 Скачать руководство пользователя страница 20

Страница: 20 / 272

Description of device parameters

Proline Promag 300 Modbus RS485

Hauser

Selection

• x

• x.x

• x.xx

• x.xxx

• x.xxxx

Factory setting

x.xx

Additional information

Description

This setting does not affect the measuring or computational accuracy of the device.

The arrow displayed between the measured value and the unit indicates that the

device computes with more digits than are shown on the local display.

Value 2 display



Navigation

 Expert → System → Display → Value 2 display (0108)

Prerequisite

A local display is provided.

Description

Use this function to select one of the measured values to be shown on the local display.

Selection

• None

• Volume flow

• Mass flow

• Correct.vol.flow

• Flow velocity

• Conductivity

• CorrConductivity

• Temperature

• Electronic temp.

• Totalizer 1

• Totalizer 2

• Totalizer 3

• Curr.output 1

• Curr.output 2

• Curr.output 3

• Curr.output 4

• Cust.trans.count

Factory setting

None

Additional information

Description

If several measured values are displayed at once, the measured value selected here will be

the second value to be displayed. The value is only displayed during normal operation.

The

Format display

parameter (→  16) is used to specify how many measured

values are displayed simultaneously and how.

Dependency

The unit of the displayed measured value is taken from the

System units

submenu

(→  55).

Visibility depends on order options or device settings

Содержание Proline Promag 300

















































































































































































































































































Результаты поиска

Содержание Proline Promag 300

Отзывы:

Похожие инструкции для Proline Promag 300

Бренды по названию

Популярные бренды

Endress+Hauser Proline Promag 300, Описание параметров устройства

Результаты поиска

Содержание Proline Promag 300

Отзывы:

Похожие инструкции для Proline Promag 300

Бренды по названию

Популярные бренды